Related Manuals for Water Tech Reionator Pro Ultra RXU13
Summary of Contents for Water Tech Reionator Pro Ultra RXU13
- Page 1 OWNERS MANUAL Whole House Water Conditioner With Triton Electronic Control Valve Activate your warranty by registering your product at watertech.com or call 469-521-1180.
- Page 2 DEALER CONTACT AND PRODUCT INFORMATION Dealer Name: Dealer Phone Number: Installation Date: Model Number: Serial Number: CUSTOMER CHECKLIST After installation, installer should make sure of the following: Customer has an Owner's Manual Customer knows how to restart system if power goes out Customer knows how to put the system in bypass in case of an emergency Customer knows what kinds of regenerant to use in brine tank Customer knows where to purchase regenerant salt or potassium chloride...
-
Page 3: Maintenance
MAINTENANCE This manual is applicable to one of the following model numbers: Pro Series: RXU13 With minimal care, your system is designed to serve you for many years. While constant attention to your system is not necessary, the following suggestions will ensure your system’s performance and your convenience and satisfaction. -
Page 4: Do's And Don'ts
DO’S AND DONT’S DO ALWAYS • check your state and local regulations regarding plumbing and electrical connections and placement of the system before installation. • install the Reionator Pro® Ultra system into the existing cold water supply line before the water heater and before any cold water outlet that requires treatment. •... -
Page 5: Parts List
PARTS LIST Triton Control Valve Overflow elbow Resin tank Brine tank MODEL RXU13 PRODUCT DESCRIPTION PART NUMBER Resin Tank 13” x 54” 09-03-1354BLK-XEMid Brine Tank Assembled 18” x 33” 09-04-1833BKNG-SIL 09-04-245 Brine Well Assembly 4.0" x 29" Brine Overflow Elbow 07-05-004 Triton Control Valve, TX 13-V1TXUMC... -
Page 6: Plumbing Connection
PLUMBING CONNECTION Typical plumbing installation Raw water to outside faucets water in Check local codes for minimum run between Reionator Pro Ulta unit and water heater Conditioned water in Triton Bypass Valve Cold IMPORTANT: Brass or Plastic yoke assembly (not shown) is required to connect piping to the bypass valve and is available in either NPT or solvent. -
Page 7: Drain Line Connection
DRAIN LINE CONNECTION Drain line elbow Locking clip Locking clip Air gap CAUTION: Never connect drain line directly into drain, sewer line or trap. Always allow an air gap of at least 25mm (1 inch) or 2 pipe diameters between the drain line and waste water to prevent the possibility of sewage being back siphoned. -
Page 8: Starting Up The System
STARTING UP THE SYSTEM Flushing, Conditioning and Sanitizing Did you connect the drain line securely to the valve? Did you connect the brine line securely to the valve? Step 1. Make sure the system is in the “Bypass” position before turning the main water back on. - Page 9 STARTING UP THE SYSTEM Check all connections to make sure the system has no leaks. Once you’ve verified all stages of regeneration are working appropriately, and have verified there are no leaks, fill the brine tank with sodium chloride or potassium chloride softening pellets. Step 3.
- Page 10 DISPLAYS & PROGRAMMING CLOCK / HOME LEFT / BACK RIGHT / NEXT SET CLOCK Press CLOCK one time. The hours will begin to flash. to adjust the hour. The hours will cycle through AM and PM. Once the hour is set correctly, press one time to set the minutes.
- Page 11 DISPLAYS & PROGRAMMING CLOCK / HOME LEFT / BACK RIGHT / NEXT SETTING REGENERATION TIME Enter the Installer Screens by pressing and holding simultaneously for 3-5 seconds. Once the display changes, press until you reach the “Regeneration Time” display. When on the “Regeneration Time” display, use to adjust the hour.
-
Page 12: Bypass Valve Operation
BYPASS VALVE OPERATION The bypass valve is typically used to isolate the control valve from the plumbing system’s water pressure in order to perform control valve repairs or maintenance. The 1" full flow bypass valve incorporates four positions including a diagnostic position that allows service personnel to work on a pressurized system while still providing untreated bypass water to the facility or residence. - Page 13 BYPASS VALVE ILLUSTRATIONS FIGURE 1. FIGURE 2. NORMAL OPERATION BYPASS OPERATION Treated Supply Supply Supply water exits water enters water exits water enters FIGURE 3. FIGURE 4. DIAGNOSTIC MODE SHUT OFF MODE POSITION Supply Supply No water Supplywater is shut off water exits water enters exits...
-
Page 14: Specifications
SPECIFICATIONS WaterTech recommends the use of Potassium Chloride (KCl) as a regenerant salt. Model Softening Efficiency @ Softening Capacity @ Max. Recommended Tank Sizes † Stated Salt Setting Stated Salt Setting (Grains Hardness (Grains Per Pound) Per Gallon) (Grains Per Gallon) 18,901 @ 4.7 lbs. - Page 15 If, upon factory inspection, the control valve body or PC board is found to be defective, Water Tech Industries will furnish repair or replacement (at WTI option) of the control valve body and/or the PC board. All internal mechanical components are warranted from manufacturers defect for a period of five (5) years from the date of installation.
- Page 16 WTI Warranty RGA policy. No person or representative is authorized to assume for Water Tech Industries any liability on its behalf, or in its name, except to refer the purchaser to this warranty. This warranty gives you specific legal rights, you may also have other rights which vary from state to state.