How To Use Your Tractor; To Set Parking Brake; To Use Throttle Control; To Move Forward And Backward - Craftsman 917.2565 Owner's Manual

OPERATIO
_AFETY GLASSEI
The operation of any tractor can result in foreign objects thrown into the eyes, which
can result in severe eye damage. Always wear safety glasses or eye shields while
operating your tractor or performing any adjustments or repairs. We recommend a wide
ViSIOn safety mask over the spectacles or standard safety glasses.
HOW TO USE YOUR TRACTOR
TO SET PARKING BRAKE (See Fig. 6)
Your tractor is equipped with an operator presence sensing
switch, When engine is running, any attempt by the
operator' to leave the seat without first setting the parking
brake wii! shut off the engine..
= Depress clutch/brake pedal into full "BRAKE" position
and hold
. Place parking brake lever in "ENGAGED" position and
release pressure from clutch/brake pedal, Pedalshould
remain in "BRAKE" position_ Make sure parking brake
will hold tractor secure_
THROTTLE/CHOKE
CONTROL,
ATTACHMENT CLUTCH LEVER
"ENGAGED" POSITION
"DISENGAGED"
POSITION
"BRAKE"
POSITION
PARKING BRAKE
"ENGAGED" POSITION
"DISENGAGED"
POSITION
CLUTCH/BRAKE PEDAL
"DRIVE" POSITION
GEARSHIFT
LEVER
NOTE: Under certain conditions when tractor is standing
idle with the engine running, hot engine exhaust gases may
cause "browning" of grass, To eliminate this possibility,
always stop engine when stopping tractor on grass areas.
i ..............
CAUTION: Always stop tractor' com-
pletely, as described above, before leav-
ing the operator's position; to empty
grass catcher, etc.
TO USE THROTTLE CONTROL (See Fig. 6)
Always operate engine at full throttle.
o Operating engine at less than full throttle reduces the
battery charging rate
= Full throttle offers the best bagging and mower perfor-
mance.,
TO MOVE FORWARD AND BACKWARD
(See Fig. 6)
The direction and speed of movement is controlled by the
gearshift lever
° Start tractor with clutch/brake pedal depressed and
gearshift lever in neutral (N) position.
o Move gearshift lever to desired position,
o Slowly release clutch/brake pedal to start movement..
IMPORTANT: BRING TRACTOR TO A COMPLETE STOP
BEFORE SHIFTING OR CHANGING GEARS. FAILURE
TO DO SO WILL SHORTEN THE USEFUL LIFE OF YOUR
TRANSAXLE.
FIG. 6
STOPPING (See Fig. 6)
MOWER BLADES -
° Move attachment clutch lever to "DISENGAGED" po-
sition.
GROUND DRIVE-
o Depress clutch/brake pedal into full "BRAKE" position,.
o Move gearshift lever to neutral (N) position.
ENGINE -
o Move throttte control to slow (._) position.
NOTE: Failure to move throttle control to slow (.e_.)
position and allowing engine to idle before stopping may
cause engine to "backfire".
° Turn ignition key to "OFF" position and remove key.
Always remove key when leaving tractor to prevent
unauthorized use..
= Never use choketo stop engine..
TO ADJUST MOWER CUTTING HEIGHT
(See Fig. 5)
The position of the attachment lift lever determines the
cutting height°
• Grasp lift lever.
o Press plunger with thumb and move lever to desired
position._
The cutting height range is approximately 1-1/2 to 4". The
heights are measured from the ground to the blade tip with
the engine not running, These heights are approximate
and may vary depending upon soil conditions, height of
grass and types of grass being mowed.
o The average lawn should be cut to approximately 2-t/2
inches during the cool season and to over 3 inches
during hot months.. For' healthier and better looking
lawns, mow often and after moderate growth,
o For best cutting performance, grass over6 inches in
height should be mowed twice.. Make the first cut
relatively high; the second to desired height_
12