Table of Contents
Advertisement
7.4 Dust Collection
The use of a dust collection system is strongly
recommended for this band saw. It will help keep the
shop clean, as well as reduce potential health
hazards caused by inhalation of wood dust. The
collector should have a capacity sufficient for this
size
machine:
600
Powermatic has a line of dust collection systems
available; see your dealer or visit our website listed
on the cover.
Connect the hoses of your dust collection system to
the saw's dust ports (4" outside diameter). Secure
tightly with hose clamps (not provided).
7.5 Electrical Connections
Electrical connections must be
made by a qualified electrician in compliance
with all relevant codes. This machine must be
properly grounded to help prevent electrical
shock and possible fatal injury.
The band saw is factory wired for 230 volts. It is
recommended that the band saw be connected to a
grounded and dedicated 20-amp circuit with a 20-
amp circuit breaker or time delay fuse. Local codes
take precedence over recommendations.
7.6 Grounding Instructions
1. All grounded, cord-connected tools:
In the event of a malfunction or breakdown,
grounding provides a path of least resistance for
electric current to reduce the risk of electric shock.
This tool is equipped with an electric cord having an
equipment-grounding conductor and a grounding
plug. The plug must be plugged into a matching
outlet that is properly installed and grounded in
accordance with all local codes and ordinances. Do
not modify the plug provided - if it will not fit the
outlet, have the proper outlet installed by a qualified
electrician.
Improper connection of the equipment-grounding
conductor can result in a risk of electric shock. The
conductor with insulation having an outer surface
that is green with or without yellow stripes is the
equipment-grounding
conductor.
replacement of the electric cord or plug is
necessary, do not connect the equipment-grounding
conductor to a live terminal.
Check with a qualified electrician or service
personnel if the grounding instructions are not
completely understood, or if in doubt as to whether
the tool is properly grounded. Use only 3-wire
extension cords that have 3-prong grounding plugs
and 3 pole receptacles that accept the tool's plug.
Repair
or
replace
damaged
immediately.
2. Grounded, cord-connected tools intended for use
on a supply circuit having a nominal rating between
150 – 250 volts, inclusive:
CFM
is
recommended.
If
repair
or
worn
cord
This tool is intended for use on a circuit that has an
outlet that looks like the one illustrated in Figure 4.
The tool's grounding plug is illustrated in Figure 4.
Make sure the tool is connected to an outlet having
the same configuration as the plug. No adapter is
available or should be used with this tool. If the tool
must be reconnected for use on a different type of
electric circuit, the reconnection should be made by
qualified service personnel; and after reconnection,
the tool should comply with all local codes and
ordinances.
Make sure the voltage of your power supply
matches the specifications on the motor plate of the
Band Saw.
7.7 Extension Cords
The use of extension cords is discouraged; try to
position machines within reach of power source. If
an extension cord becomes necessary, make sure
the cord rating is suitable for the amperage listed on
the machine's motor plate. An undersized cord will
cause a drop in line voltage resulting in loss of
power and overheating.
Use Table 1 as a general guide in choosing the
correct size cord. The smaller the gauge number,
the heavier the cord. If in doubt, use the next heavier
gauge.
Recommended Gauges (AWG) of Extension Cords
Amp Rating
Not
More
More
Than
Than
0
6
6
10
or
10
12
12
16
7.8 Rail and Guide Rail
Refer to Figure 5a.
1. Install the rail to the front edge of the table,
using two (2) M6x16 socket head button screws
(HP-1), with M6 lock washers (HP-4), and M6
flat washers (HP-3), through the slotted holes in
the rail. Place the screws approximately in the
center of the slots; this can be adjusted later as
11
Figure 4
Volts Total length of cord in feet
120
25
50
100
240
50
100
200
AWG
18
16
16
18
16
14
16
16
14
14
12
Not Recommended
Table 1
150
300
14
12
12
Advertisement
Table of Contents
