Download Print this page

ekwb EK-FB EVGA X58 LE Installation And Mounting Manuals

Advertisement

Quick Links

Installation and mounting manual for EK-FB EVGA X58 LE water block:
This product is intended for installation only by expert users. Please consult with a qualified technician for installation. Improper installation may result in damage to your equipment. EK Water Blocks assumes no liability
whatsoever, expressed or implied, for the use of these products, nor their installation. The following instructions are subject to change without notice. Please visit our web site at
Before installation of this product please read important notice, disclosure and warranty conditions printed on the back of the box.
The barb hose fittings require only a small amount of force to screw them in; otherwise the high flow fittings might break. These fittings do not need to be tightened with much force because the
liquid seal is made using o-rings.
STEP 1: GENERAL INFORMATION Sample photo of EVGA X58 LE PCB design
STEP 2: PREPARING YOUR MOTHERBOARD
1. REMOVING STOCK COOLER. Remove all encircled screws.
cooler assembly screws should be removed. There are 6 screws on the back of
the motherboard.
3. APPLYING THERMAL COMPOUND
Apply thermal compound: lightly coat the Northbridge with for example
Céramique™
thermal
compound.
cooling.com/catalog/product_info.php?cPath=39_&mID=127&language=en
detailed instructions. EKWB recommends non-conductive MX-2, which should
be applied in cross form for best performance (see sample picture).
5. PLACING THERMAL PADS ON MOTHERBOARD. Place thermal pads you cut on PCB as shown on picture bellow. (PLEASE REMOVE FOIL OF THERMAL PADS
PRIOR TO INSTALLATION.)
25x25x0,5mm 
All disclosures, notices and warranty conditions are being written on the back of the box.          
North bridge 
South bridge 
All stock
Follow
this
link
http://www.arctic-
12x4x1mm
12x4x0,5mm
2. CLEANING THE PCB.
Carefully detach the original stock cooler after removing all screws
securing it to the board. Wipe off the remains (by using non–abrasive cloth or qtip, as shown
on sample photo) of the original thermal compound until the components and circuit board are
completely clean. EKWB does not recommend using any liquids for removing paste.
4. CUTTING THERMAL PADS.
pads are enclosed with your water block. Please cut thermal pads as shown bellow.
(WARNING: DIMENSIONS ON PICTURES BELLOW ARE SCALED!)
for
Apply thermal grease here.
 
www.ekwaterblocks.com
Mosfets 
CPU socket 
One thermal pad (90x15x1 mm) and 2 (30x25x0,5) thermal
18x4x1mm
18x4x0,5mm
75x7,5x1mm
 
 
 
          Released on 7
for updates.
th
 of August, 2009. 

Advertisement

loading
Need help?

Need help?

Do you have a question about the EK-FB EVGA X58 LE and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for ekwb EK-FB EVGA X58 LE

  • Page 1 Installation and mounting manual for EK-FB EVGA X58 LE water block: This product is intended for installation only by expert users. Please consult with a qualified technician for installation. Improper installation may result in damage to your equipment. EK Water Blocks assumes no liability whatsoever, expressed or implied, for the use of these products, nor their installation.
  • Page 2 STEP 6: POSITIONING FITTINGS AND CONNECTING TO WATER CIRCUIT 1.Screw in fittings as shown in photo, attach the liquid cooling tubes and connect the water-block(s) into the cooling circuit. The EK-FB EVGA X58 LE series are usually sold with high flow fittings. To ensure that the tubes are securely attached to the barb fittings, please use hose clamps or an appropriate substitute. The use of an algaecide is always recommended for any liquid cooling system.