EINHELL TP-CS 18/190 Li BL Operating Instructions Manual page 15

•
Check that the swing guard hood works
properly. The swing guard hood must not jam,
and it must return to its initial position when
you have completed the cut.
•
Before you use the circular saw, check the
function of the swing guard hood with the
battery disconnected.
•
Before you use the machine, make sure that
the safety equipment such as the swing guard
hood, flanges and adjustment devices are in
working order and are correctly adjusted and
secured.
•
You can connect a suitable dust extraction
system to the sawdust extraction connector
(14). Make sure that the dust extraction
system is safely and correctly connected.
•
The moving swing guard hood must not be
fixed in the retracted guard hood when the
saw is in use.
6.2 Using the cordless hand-held circular
saw
•
Adjust the cutting depth, cutting angle and
parallel stop (see section 5.1, 5.2 and 5.4)
•
Do not switch on the circular saw until you
have fitted a saw blade.
•
Place the saw foot flat on the workpiece you
want to saw. The saw blade must not be in
contact with the workpiece.
•
Hold the circular saw firmly with both hands.
6.3 Switching On/Off (Fig. 11)
Switching on:
Press the locking button (3) and the On/Off switch
(2) at the same time.
•
Allow the saw blade to accelerate until it
reaches full speed. Then slowly move the saw
blade along the cutting line. Exert only gentle
pressure on the saw blade as you do so.
Switching off :
Release the locking button and ON/OFF switch
•
When you let go of the handle, the machine
will shut down automatically. It is impossible
therefore for the saw to run unintentionally.
•
Ensure that you do not cover or block the
ventilation openings while working with the
tool.
•
After you have switched off the saw, do
not slow down the saw blade by applying
pressure to its side.
•
Important! Do not put down the machine
until the saw blade has reached a complete
standstill.
Anl_TP_CS_18_190_Li_BL_USA_SPK7.indb 15 Anl_TP_CS_18_190_Li_BL_USA_SPK7.indb 15
EN
Important! Carry out a trial cut in a piece of
waste wood.
6.4 Changing the saw blade (Fig. 12-16)
Warning!
Always remove the battery pack before making
adjustments to the equipment.
Use only saw blades which are of the same type
as the saw blade supplied with this circular saw.
Ask your dealer for advice.
Warning!
Do not use grinding wheels!
The diameters of the saw blades used must
correspond to the diameters specifi ed on the
hand-held circular saw blade!
Use only recommended saw blades!
Use the saw blade key (13) supplied to change
the saw blade. The saw blade key (13) is stored
in the housing. If required, pull the saw blade key
(13) out of the housing (see Figure 13).
Important! For safety reasons, the cordless
hand-held circular saw must not be operated with
the saw blade key (13) inserted in it.
•
Press the spindle lock (11).
•
Undo the screw (clockwise) to secure the saw
blade (17)
•
Push back and secure the moving swing
guard hood (20) using the lever for the swing
guard hood (21).
•
Remove the flange (18) and the saw blade
(12) in a downwards direction.
•
Clean the flange and insert the new saw
blade. Pay attention to the running direction
(see arrow on the guard hood and saw
blade).
•
Tighten the screw (counterclockwise) to
secure the saw blade (17) and check that the
blade runs true.
•
Before you press the On/Off switch, make
sure that the saw blade is correctly fitted
and that moving parts run smoothly and the
clamping screws are tightened securely.
6.5 LED lamp (Fig. 1/Item 5)
The LED lamp (5) can be used in poor lighting
conditions to additionally illuminate the cutting
position. The LED light (5) will come on
automatically as soon as you press the locking
button for the On/Off switch (3).
- 15 -
19.04.2022 15:37:15 19.04.2022 15:37:15