Before Starting The Equipment; Operation - EINHELL TP-CS 18/190 Li BL Operating Instructions Manual

5. Before starting the equipment

Warning!
Always remove the battery pack before making
adjustments to the equipment.
5.1 Setting the cutting depth (Figure 2/3)
•
Release the handle on the rear of the guard
hood for adjusting the cutting depth (4).
•
Place the soleplate (6) flat on the surface
of the workpiece you wish to saw. Raise the
saw until the saw blade (12) is at the required
cutting depth (22).
•
Tighten the handle for adjusting the cutting
depth (4). Check that everything is securely
fastened.
5.2 Miter stop (Figure 4/5)
•
The preset standard angle between the saw
foot (6) and the saw blade (12) is 90°. You can
adjust this angle to carry out angled cuts.
•
Release the locking lever for miter setting (7)
on the front of the saw foot.
•
You can now adjust the cutting angle by up to
45°. Keep an eye on the cutting angle scale
(9) as you do so.
•
Refasten the locking screw for miter setting
(7). Check that everything is securely
fastened.
5.3 Extraction of dust and chips (Fig. 6)
•
Connect a suitable vacuum cleaner to the
provided sawdust extractor connection (14)
of your circular saw (vacuum cleaner not
included). This will ensure optimum dust
extraction from the workpiece. The benefits
are that you will protect both the equipment
and your own health. Your work area will also
be cleaner and safer.
•
Dust created when working may be
dangerous. Refer to the section entitled
"Safety instructions".
•
Important! The vacuum cleaner you use for
the vacuum extraction must be suitable for
the material you are cutting.
•
Check that all parts are properly joined
together.
5.4 Edge guide (Figure 7/8)
•
The edge guide (16) enables you to saw
parallel lines.
•
Loosen the locking screw for the edge guide
(8) on the saw foot (6).
•
To assemble, slide the edge guide (16) into
Anl_TP_CS_18_190_Li_BL_USA_SPK7.indb 14 Anl_TP_CS_18_190_Li_BL_USA_SPK7.indb 14
EN
the guide (23) on the saw foot (6) (see Fig. 7)
•
Set the required distance and then tighten the
locking screw (8) again.
•
Using the edge guide: Position the parallel
stop (16) flat on the edge of the workpiece
and start the sawing.
Important! Carry out a trial cut in a piece of
waste wood
5.5 Line guide (Fig. 9)
Using the line guide (15) you can carry out
exact cuts following cutting lines marked on the
workpiece. Use the mark for the 0° or 90°angle
setting and the mark for the 45° angle setting.
For information on the angle setting see 5.2
Important! Carry out a trial cut in a piece of
waste wood

6. Operation

Warning!
Always remove the battery pack before making
adjustments to the equipment.
6.1 Working with the cordless hand-held
circular saw
•
Always hold the tool firmly by the handles
provided (1 and 10) to ensure that you handle
it safely when using it.
•
The swing guard hood (20) is pushed back
automatically by the workpiece.
•
Do not use force! Push forwards gently and
evenly with the circular saw.
•
The waste piece should be on the right-hand
side of the circular saw so that the wide
section of the support bench supports its full
area.
•
If you are sawing down a line that has been
drawn, guide the circular saw along the
corresponding notch.
•
Clamp small pieces of wood securely before
sawing them. Never hold them with your
hand.
•
Always follow the safety instructions. Wear
safety goggles.
•
Do not use defective saw blades or blades
that are cracked or broken.
•
Do not use any flanges / flange nuts whose
bore hole is larger or smaller than those in the
saw blade.
•
The saw blade must not be decelerated by
hand or by applying lateral pressure to the
blade.
- 14 -
19.04.2022 15:37:15 19.04.2022 15:37:15