Table of Contents
Advertisement
GETTING TO KNOW YOUR CLEANER
A.
Accessory Door
B.
Main Cleaner
C.
Bag Door
D.
Mechanical Bag Check Indicator*
E.
On/Off Pedal
F.
Exhaust Filter Cover
G.
Cord Reel Pedal
H.
Variable Power Control Slider**
H1. LED Display Screen With Variable Power Controls** and Led Bag Check Indicator*
I.
Carry Handle
J.
Bag Door Release Latch
K.
Hose
L.
Suction Regulator
M.
Hose Handle
N.
Telescopic Tube
O.
Telescopic Tube Adjuster
P.
Floor Type Selector Pedal*
Q.
Carpet and Floor Nozzle**
R.
Bag-motor filter
S.
Bag Holder
T.
Exhaust Filter
Ua. Pre-Motor Filter
U.
Ub. Pre-Motor Filter Frame
r
V.
Accessory Set
W1. Crevice Tool
W2. Furniture Nozzle
W3. Dusting Brush
W.
Pet Hair Remover Mini Turbo Nozzle*
X.
Allergen Remover Mini Turbo Nozzle*
Y.
Parquet Nozzle*
ASSEMBLING YOUR CLEANER
Remove all components from the packaging.
1.
Connect the hose to the cleaner main body, ensuring it clips and locks into position.
To release the hose: simply press the two latches on the hose end and pull. [1]
Connect the hose handle to the upper tube end. [2]
2.
Connect the tube lower end to the carpet and floor nozzle** or accessories if required. [3]
3.
*Certain Models Only
** May vary according to model
USING YOUR CLEANER
1.
Extract power cord and plug it into the power supply. Do not pull the cord beyond the
red marker. [5]
2.
Adjust the telescopic tube to the desired height by moving the telescopic tube and raise
or lower the tube to the most comfortable cleaning position. [4]
3.
After connecting the telescopic tube lower end to Carpet and Floor Nozzle** or
accessories if required, press the floor type selector* pedal on the nozzle to select
the ideal cleaning mode for the floor type.
Hard Floor – Brushes are lowered to protect the floor.
Carpet – Brushes are raised for deeper cleaning.
4.
Switch the cleaner on by pressing the On/Off Pedal on the cleaner main body. [6]
5.
Adjust the power level by pressing the variable power control buttons on the
display** [7] or by adjusting the variable power control slider**. [8]
6.
Adjust the suction regulator to the desired level.[9]
7.
Switch off at the end of use by pressing the On/Off Pedal. Unplug and extract power
cord again to wind the power cord back into the cleaner.
8.
Parking and Storage - The tube can be parked for temporary storage while in use, or
in the storage position when not in use. [10]
ACCESSORIES
The Crevice tool, Furniture nozzle and Dusting brush are stored on board under
the accessories door.
All accessories can be fitted to the end of the handle or the end of the telescopic tube.
Accessory Set:
Crevice Tool – For corners and hard to reach areas. [V1]
Furniture Nozzle – For soft furniture and fabrics.[V2]
Dusting Brush – For bookshelves, frames, keyboards and other delicate areas. [V3]
Parquet Nozzle* – For parquet floors and other delicate floors. [Y]
Pet Hair Remover Mini Turbo Nozzle* - Use the mini turbo nozzle on stairs or for deep
cleaning on textile surfaces and other hard to clean areas. Particularly suitable for pet
hairs removal. [W]
Allergen Remover Mini Turbo Nozzle* – Use the mini turbo nozzle on stairs or for deep
cleaning on textile surfaces and other hard to clean areas, particularly suitable for allergen
removal. [X]
IMPORTANT: Do not use mini turbo nozzles on rugs with long fringes, animal hides and
carpet pile deeper than 15mm. Do not keep the nozzle stationary while brush is rotating.
2
GB
Advertisement
Table of Contents
