Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for DeWalt DCM200E2T
Summary of Contents for DeWalt DCM200E2T
- Page 1 DCM200...
- Page 2 English (original instructions) Copyright D WALT...
- Page 3 Fig. A Fig. B...
- Page 4 Fig. C Fig. D Fig. E1 Fig. E2 Fig. E3 Fig. G Fig. F...
- Page 5 Fig. H Fig. I Fig. J Fig. K Fig. L Fig. M...
- Page 6 Fig. N Fig. O Fig. Q Fig. P Fig. R Fig. S...
- Page 7 Fig. T Fig. U Fig. V Fig. W Fig. X...
- Page 8 English BANDFILE DCM200 Congratulations! 2006/42/EC, EN62841‑1:2015+A11:2022, EN62841‑2‑4:2014 + AC:2015. You have chosen a D WALT tool. Years of experience, thorough These products also comply with Directive 2014/30/EU and product development and innovation make D WALT one of the 2011/65/EU. For more information, please contact D WALT at most reliable partners for professional power tool users.
-
Page 9: Definitions: Safety Guidelines
English Batteries Chargers/Charge Times (Minutes)*** DCB112/ DCB115/ Weight (kg) DCB104 DCB107 DCB113 DCB116 DCB117 DCB118 DCB132 DCB119 Cat # DCB1102 DCB1104 DCB546 18/54 6.0/2.0 1.08 DCB547/G 18/54 9.0/3.0 1.46 135* 110* 135* DCB548 18/54 12.0/4.0 1.46 DCB181 0.35 DCB182 0.61 60/40** 60/45** 60/40** 60/40** DCB183... - Page 10 English 3) Personal Safety power tool’s operation. If damaged, have the power tool repaired before use. Many accidents are caused by a ) Stay alert, watch what you are doing and use poorly maintained power tools. common sense when operating a power tool. Do not f ) Keep cutting tools sharp and clean.
-
Page 11: Residual Risks
English Belt Sander Supplemental Safety Warnings Personal safety • No children or pregnant women should enter the work area • Always use proper eye protection and a respirator where the paint sanding is being done until all clean‑up when sanding. is completed. •... -
Page 12: Important Safety Instructions For All Battery Chargers
English Your D WALT charger is double insulated in Pull by plug rather than cord when disconnecting • accordance with EN60335; therefore, no earth wire charger. This will reduce risk of damage to electric plug is required. and cord. If the supply cord is damaged, it must be replaced only by Make sure that cord is located so that it will not be •... -
Page 13: Wall Mounting
English nOTE: To remove the battery pack, some chargers require the drywall screws (purchased separately) at least 25.4 mm long battery pack release button to be pressed. with a screw head diameter of 7–9 mm, screwed into wood to 14 an optimal depth leaving approximately 5.5 mm of the screw Refer to the indicators below for the charge status of the exposed. -
Page 14: Storage Recommendations
English Transporting the FlEXVOlT Battery has received a sharp blow, been dropped, run over or damaged in any way (i.e., pierced with a nail, hit with The D WALT FLEXVOLT® battery has two modes: Use a hammer, stepped on). Electric shock or electrocution and Transport. -
Page 15: Package Contents
English Markings on Tool Have defective cords replaced immediately. The following pictograms are shown on the tool: Read instruction manual before use. Charge only between 4 ˚C and 40 ˚C. Wear ear protection. Only for indoor use. Wear eye protection. Discard the battery pack with due care for the environment. - Page 16 English • This product is not intended for use by persons (including 3. Check that the spring 18 is located in its mounting hole. children) suffering from diminished physical, sensory or 4. Position the arm or as shown. 8 17 mental abilities; lack of experience, knowledge or skills 5.
- Page 17 The DCM200DC dust shroud is compatible with the DWH161 • Set the variable speed dial 1 to the required setting. DEWALT Universal Dust Extractor (sold separately). • Friction‑fit the dust port 11 to the hose 25 of the DWH161 Switching On and Off (Fig. A)
-
Page 18: Hints For Optimum Use
English Special Applications (Fig. A, R–V) Your tool is Tool Connect™ Chip ready and has a location for installation of a Tool Connect™ Chip. WARNING: To reduce the risk of fire or serious injury, Tool Connect™ Chip is an optional application for your avoid sanding ignitable materials such as aluminum smart device (such as a smart phone or tablet) that connects and magnesium. -
Page 19: Optional Accessories
English Optional Accessories WARNING: Since accessories, other than those offered by D WALT, have not been tested with this product, use of such accessories with this tool could be hazardous. To reduce the risk of injury, only D WALT‑recommended accessories should be used with this product. Consult your dealer for further information on the appropriate accessories. - Page 20 Belgique et WALT ‑ Belgium BVBA Tel: NL 32 15 47 37 63 www.dewalt.be luxembourg België en luxemburg enduser.BE@sBDinc.com Egide Walschaertsstraat 16 Tel: FR 32 15 47 37 64 2800 Mechelen Fax: 32 15 47 37 99 Danmark WALT (Stanley Black&Decker AS)