GENERAL INFORMATION GENERAL INFORMATION Precautions The operation of any appliance that uses fuel, electrical power General Safety Information and water demands that a number of fundamental safety pre- cautions be respected: This product must be installed by a legally qualified heat- Do not allow children or infirm persons to operate the sys- ing engineer.
The control panel, apart from managing the functions of the LN is a hot water generator for the heating of environments and thermal unit INSIEME EVO COND B/130 LN, allows highlighting any production of domestic hot water (DHW) by means of a vitrified anomaly which may affect its correct operation, ensuring the heater.
GENERAL INFORMATION System layout INSIEME EVO COND B/130 LN Electric actuator 3-way diverting valve Main switch Central heating flow Heating safety valve Central heating return Condensate drain siphon Storage cylinder expansion vessel Domestic hot water outlet 10 Domestic cold water inlet...
GENERAL INFORMATION Control panel Controls interface Door Light guide Rear light display ENTER/RESET key: it allows accessing the main menu and restoring the operation after a stop due to an anomaly Navigation keys Main switch (located on the equipment rear wall) Light Guide displaying STATUS DESCRIPTION...
Page 8
GENERAL INFORMATION Display visualisation HEAT °C °F OUTSIDE Icon displayed when heating mode is enabled. Blinking when there is a heat demand Icon displayed when DHW mode is enabled. Blinking when there is an DHW Demand Icon displayed when entering the "Installer" menu Icon displayed when the burner of the equipment is on.
GENERAL INFORMATION Menu navigation At start-up or when no key is pressed for more than 4 minutes, the display is in “basic display” mode and provides general infor- mation on the equipment operation. In this mode, keys have the following functions: Button Function "+"...
Page 10
GENERAL INFORMATION MENU selection Access the “menu” mode by pressing the key “ENTER/RESET” The digits of the small display indicate “0000”, which is the first acces- sible menu. In this mode, keys have the following functions: Button Function "+" Exits from the menu and cancels a parameter change "-"...
GENERAL INFORMATION List of user parameters Par. Default Menu Description Range setting Main menu Quick adjustment of direct Zone/Zone 1 heating setpoint in 0 and 3 heating modes. By connecting the zone control accessory, this parameter See Par. 0000 See Par. 2103 °C can be used to quickly change direct Zone/Zone 1 setpoint.
Page 13
GENERAL INFORMATION Par. Default Menu Description Range setting Direct Zone / Zone 1 Heating Settings Direct Zone/Zone 1 setpoint in heating mode Par. 2001= 0 If Zone 1 is not ena- and 3 bled: The thermal unit adjustment determines the boiler set- (Par.
2 USE 2.1.2 Start-up Once you have completed all the checks listed above, proceed as Putting into service follows to start up the boiler for the first time: − set the main switch of the system to ON and the main switch of the equipment to (I).
Page 15
Firmware version of the thermal unit regulator. To switch off the equipment, set the main switch to “0”. In the example the message indicates a firmware version = 1. Never power off the appliance before switching the master switch to the "0" position. Never switch off the appliance with the master switch if a request is active.
2.1.3 Adjustment of heating setpoint 2.1.5 Enable/disable the domestic function − Press the key“+” or “-” to display the current value of the − Press the keys "▲" and "▼" simultaneously for a few heating temperature setpoint. seconds; − The icon and the current domestic mode (ON or OFF) will blink on the display;...
2.1.7 Special functions Venting The function is automatically enabled at the first start-up and at When a special function is active, a specific message is shown each reset of the power supply. on the display of the device control interface. When the function is active, the message “Air”...
2.1.8 Ignition failure Temporary or short-term shut-down If an ignition or operating anomaly occurs, the thermal unit dis- In the event of temporary or short-term shut-down (e.g. due to play will show a text message (small digit) and a number (large holidays), proceed as follows: digit), which vary according to the anomaly detected.
Device cleaning and maintenance Please remember that THE PERSON RESPONSIBLE FOR SYSTEM MAN- AGEMENT MUST ENSURE THAT PROFESSIONALLY QUALIFIED HEATING ENGINEERS UNDERTAKE PERIODIC MAINTENANCE AND COMBUSTION EFFICIENCY MEASUREMENTS. ’s Technical Assistance Service is qualified to satisfy these legal requirements and can also provide useful information on MAINTENANCE PROGRAMMES designed to guarantee: −...
Troubleshooting FAULT CAUSE SOLUTION − Contact your local Technical Assistance There is a smell of fumes Fumes escaping into the air Service − Contact your local Technical Assistance Air in the circuit Service The generator is at temperature but the heating system is cold −...
RECYCLING AND DISPOSAL 3 RECYCLING AND DISPOSAL At the end of the life cycle, safely remove the components and dispose of them in a responsible manner, in compliance with The device is primarily composed of: the installation country's applicable environmental legislation. Material Component Adequate sorted waste collection, processing and environ-...
Page 24
RIELLO S.p.A. Via Ing. Pilade Riello, 7 37045 - Legnago (VR) www.riello.com The manufacturer strives to continuously improve all products. Appearance, dimensions, technical specifications, standard equipment and accessories are therefore liable to modification without notice.