SAFETY INSTRUCTIONS When correctly installed in compliance to installation instructions and adhering to all current electrical, mechanical and manufacturer regulations, your automation system will provide a high degree of safety and problem free operation. Please take note of the following warnings that must be followed in order to prevent accidents during your gate operation: •...
Page 4
TYPICAL GATE SETUP OUTSIDE OF GATES INSIDE OF GATES FROG Motor with Flashing Light (optional) Mechanical End Stop (not supplied) Foundation Box Selector Keypad (optional) Photocell column (optional accessory) 10 Latch Control Panel Photocells (on outside of gate posts) Reception Antenna 2nd set of Photocells (optional) CONTROL PANEL •...
GEOMETRY Preliminary checks Tick 1. Check that the gate structure is sturdy enough, the hinges work efficiently and that there is no friction between the fixed and moving parts 2. Check that the foundation box is correctly installed 3. Make sure that you have fitted opening and closing mechanical gate stops 4.
MANUAL RELEASE The FROG underground system is supplied with one of three release mechanisms; a triangular key system , a DIN key system or a lever system To manually release the gates: 1. Lift tab. 2. Insert DIN key, traiangular key or lever into the lock and turn 90 to release 3.
wiring diagram ZM3E Control Panel Set RSE jumper to OFF AF43S Plug-in 11 ES TS CY CZ FA1 FC1 FA2 FC2 B1 B2 Mains Supply TOP-A433N 230 V AC Antenna Cable/length Cable/length 1m - 20m = 3 Core 1.5mm RG58 20m - 30m = 3 Core 2.5mm Max.
Page 8
Approx. 5+ gate manoeuvres per 1-3 Years day, multiple scenarios running Due to situations outside of our control, CAME cannot guarantee signal strength or availability and therefore will not be held liable for lack of service. setup app for the installer...
230V 230V TITLE initial power ON Power on the control board. The display will read WWW.CAME.COM ZM3E Keycode 123456789ABCDE F MATR 54051 6 RGSM001S 300mAE GSM – 900 33dBm GSM LED (Blue) DCS – 1800 30dBm 1A 30V After a few seconds the LED will flash 1x/sec 869.5MHz...
Page 10
Mr Wilson, Sills Road, DE74 2US Mr Wilson, Sills Road, DE74 2US 3.1 Open the App and log in 3.2 Select “CAME Connect 3.3 Select “Installations 3.4 Select “New Installation”. using your technician details connection”.
Page 11
3.7 Press “Add gateway”. 3.8 Press ‘Manual Add’. “Description” and then press created. “Add”. 3.9 To ensure future visibility in both the CONNECT Setup App and CAME Automation App we recommend you should complete the details as shown below: 123456789ABCDEF 123456789ABCDEF 123456789ABCDEF...
Page 12
TITLE commissioning the rgsm the importance of naming your gateway correctly getting it right at the start can save lots of time in the future for installers Device confi gured By naming the gateway to our recommendation, should you need to access the SIM number for Online future top-up purposes, you will be able to do this using the Installer Setup App.
Page 13
TITLE commissioning the rgsm adding the rgsm gateway to your technician account (continued) 3.10 The RED and GREEN LED’s will now be on solid and the BLUE fl ashing 1x/sec. CONGRATULATIONS - the RGSM001S has now been successfully added to the Connect platform Keycode 123456789ABCDE F troubleshooting...
Page 14
TITLE COMMISSIONING VIA APP adding Ensure the wiring is complete (refer to the wiring diagram) & any required automation physical stops are set before commencing with programming. FROG (230V) - ZM3E - Automation for swing gates Front Gates Front Gates Installer Tip The Name and Description entered here, can be used to identify the...
Page 15
TITLE COMMISSIONING VIA APP Set the Opening Delay M1 Set the safety inputs (please Select Calibrating Travel. and Closing Delay M2 to the refer to section 12 for desired value (secs). Select options). Select Next. Next. When the gate has successfully Select Add.
Page 16
COMMISSIONING VIA APP Once it has been accepted on Select the back button to If you select ADD via QR Once the QR code has been the control panel It will display return to the main menu. Code, the app will open the scanned, enter a Name and the above screen.
Page 17
TITLE COMMISSIONING VIA APP transfer to customer name@mycustomer.co.uk name@mycustomer.co.uk Firstname Lastname To transfer to a customer, Select Transfer site Enter customer details you Select confi rm. The customer select the 3 dots. wish to transfer to. will get an email asking to confi rm the account.
Page 18
Safety inputs should now be configured and the gate force tested as required. Please refer to the full manual to complete the commissioning. Should the gates not operate as suggested above, call CAME helpline 0115 921 0430 for technical support.
Page 19
– Choose the type of radio coding for the transmitters All decoding – (default) Rolling code TW key block To confi rm ( Should the transmitter not operate as suggested above, call CAME helpline 0115 921 0430 for technical support.
TITLE SAFETY options SAFETY INPUTS FUNCTIONS > CX Input, CY Input, CZ Input REOPENING DURING CLOSING • When the automation is in its closing cycle and the safety circuit is triggered the automation will stop and reverse its motion until it reaches its fully open position again.
Page 21
replacing the sim card A third party SIM card may be used, for example, if an existing SIM card is available or the current SIM data contract expires. To insert a SIM card please do the following: With the power switched to the control panel, remove the RGSM casing, slide out the existing SIM card and fi t the replacement SIM card into the slot.
optional ACCESSORIES Code(s) Description RADIO KEYPAD SELECTORS 806SL-0170 SELT1W4G - Surface-mounted, 433.92 MHz radio-frequency keypad selector, 12-keys, with blue backlighting. 25 savable codes and password to access the programming mode. Settable in Rolling Code or Fixed Code mode. RAL7024 Grey colour. 806SL-0180 SELT1W8G - Surface-mounted, 868.35 MHz radio-frequency keypad selector, 12-keys, with blue backlighting.
Page 23
Black anodised aluminium post. H = 500mm 001DIRCG Silver RAL9006, PVC post. H = 500mm CAME KEY 806SA-0110 WiFi internet gateway. Communicate directly with your smartphone or tablet, allowing you to manage the configuration of your device with no need for an internet connection.
Page 24
User to submit a contractual offer, which will be submitted by password. fi lling in the Form. Came reserves the right to accept or reject said offer. Except in the event that a third party violates the Came computer systems, the User shall be exclusively responsible for maintaining the 4.3 The Contract will be considered concluded at the moment in which the...
Page 25
Italy, by the Italian conditions, Came will not be in any way liable for the failed or faulty Legislative Decree dated 6 September 2005, no. 206, “Consumer provision of the Service, nor will it be liable for any loss, damage or Code”, with specifi...
Page 26
Court of Treviso (Italy). CAMECONNECT 8.3 Came reserves the right to make changes to the Terms of Use at any 3.1 CameConnect has the features described in detail in the User Manual. time, publicising them on this page. In the event of a failure to accept the changes made to the Terms of Use, the Installer may withdraw 3.2 The features of the Software and CameConnect are subject to change...
Page 27
TITLE TITLE terms and conditions General Terms and Conditions of 1NCE GmbH for M2M/IoT mobile communications services (version as of 07/2018) 3.1 lit. c) of these GTC. 1NCE expressly points out that the type and Scope of application scope of such services of the respective mobile network operators, 1.1 The following General Terms and Conditions (hereinafter referred to as in particular also the respective available transmission technologies “GTC”) shall govern any and all contracts relating to the provision of...
Page 28
TITLE terms and conditions of receipt of the relevant Chip Cards by the Customer. Liability for Section 3.3 sentence 2 of these GTC shall be determined by the price damages due to defects is limited in accordance with the provisions of list of 1NCE valid at the time of this purchase.
Page 29
TITLE terms and conditions 10.2 The Parties also undertake to treat all other confi dential information Liability of the other Party that the receiving Party becomes aware of in Any liability of 1NCE for damages and/or reimbursement of expenses connection with the contractual relationship as strictly confi dential arising from or in connection with the contractual relationship between and not to disclose such information to any third party for an unlimited 1NCE and the Customer shall be subject to the following limitations:...
Page 32
YOU MAY NOT EVEN PARTIALLY REPRODUCE THIS DOCUMENT CAME RESERVES THE RIGHT TO MAKE ANY CHANGES TO THIS DOCUMENT AT ANY TIME THE DATA AND INFORMATION SHOWN IN THIS CATALOGUE ARE SUBJECT TO CHANGE WITHOUT OBLIGATION TO GIVE PRIOR NOTICE BY CAME S.P.A, E&OE CAME S.p.A.