Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for CAME 8K01MP-0408
Summary of Contents for CAME 8K01MP-0408
- Page 1 CAME.COM/UK 8K01MP-0408 ATS kit Complete kit for a pair of swing gates weighing up to 400kg per leaf / max. width 3m QUICK SETUP GUIDE Typical gate setup & geometry Gate motor manual release Kit wiring diagram Control panel guide & safety...
-
Page 2: Table Of Contents
Typical Gate Setup Commissioning via App Geometry Commissioning via Panel Manual Release Instructions Safety Options Wiring Diagram Replacing the SIM Card Pre-installed SIM Card Optional Accessories 8K01MP-0408: KIT CONTENTS ATS30DGS ZL65 AF43S Control Panel Radio Frequency Card Motor TOP44RBN top-a433n DIR10... -
Page 3: Safety Instructions
SAFETY INSTRUCTIONS When correctly installed in compliance to installation instructions and adhering to all current electrical, mechanical and manufacturer regulations, your automation system will provide a high degree of safety and problem free operation. Please take note of the following warnings that must be followed in order to prevent accidents during your gate operation: •... -
Page 4: Typical Gate Setup
TYPICAL GATE SETUP OUTSIDE OF GATES INSIDE OF GATES ATS Motor Flashing Light (optional) 2nd set of Photocells (optional) Control Panel Selector Keypad (optional) Mechanical End Stop (not supplied) Reception Antenna Photocells (on outside of gate posts) Photocell column (optional accessory) CONTROL PANEL •... -
Page 5: Geometry
GEOMETRY Preliminary checks Tick 1. Check that the gate structure is sturdy enough, the hinges work efficiently and that there is no friction between the fixed and moving parts 2. Make sure that measurement does not exceed the value shown in the reference table 3. -
Page 6: Manual Release Instructions
MANUAL RELEASE The ATS telescopic swing gate operators have a manual release lock beneath a hatch on the top of the motors. To manually release the gates: 1. Open the hatch covering the lock 2. Insert release key into lock and turn clockwise 3. -
Page 7: Wiring Diagram
wiring diagram ZL65 Control Panel Set RSE jumper to OFF AF43S Plug-in 3P 7 10 TS 2 CX CY M1 N1 ENC1 M2 N2 ENC2 TOP-A433N Antenna Cable/length RG58 Max. 5m Mains Supply 230 V AC Cable/length 1m - 20m = 3 Core 1.5mm 20m - 30m = 3 Core 2.5mm 10 2 A B GND RGSM001S... - Page 8 Approx. 5+ gate manoeuvres per 1-3 Years day, multiple scenarios running Due to situations outside of our control, CAME cannot guarantee signal strength or availability and therefore will not be held liable for lack of service. setup app for the installer...
- Page 9 TITLE initial power ON Power on the control board. Keycode 123456789ABCDE F MATR 54051 6 RGSM001S 300mAE GSM – 900 33dBm GSM LED (Blue) DCS – 1800 30dBm 1A 30V After a few seconds the LED will flash 1x/sec 869.5MHz 14dBm indicating the RGSM001S is registered on a CONNECT...
- Page 10 Mr Wilson, Sills Road, DE74 2US Mr Wilson, Sills Road, DE74 2US 3.1 Open the App and log in 3.2 Select “CAME Connect 3.3 Select “Installations 3.4 Select “New Installation”. using your technician details connection”.
-
Page 11: Commissioning The Rgsm
3.7 Press “Add gateway”. 3.8 Press ‘Manual Add’. “Description” and then press created. “Add”. 3.9 To ensure future visibility in both the CONNECT Setup App and CAME Automation App we recommend you should complete the details as shown below: 123456789ABCDEF 123456789ABCDEF 123456789ABCDEF... - Page 12 TITLE commissioning the rgsm the importance of naming your gateway correctly getting it right at the start can save lots of time in the future for installers Device confi gured By naming the gateway to our recommendation, should you need to access the SIM number for Online future top-up purposes, you will be able to do this using the Installer Setup App.
- Page 13 TITLE commissioning the rgsm adding the rgsm gateway to your technician account (continued) 3.10 The RED and GREEN LED’s will now be on solid and the BLUE fl ashing 1x/sec. CONGRATULATIONS - the RGSM001S has now been successfully added to the Connect platform Keycode 123456789ABCDE F troubleshooting...
- Page 14 TITLE COMMISSIONING VIA APP adding Ensure the wiring is complete (refer to the wiring diagram), the micro limit switch end- of-travel points are set (refer to the ATS manual) & any required physical stops are set automation before commencing with programming ZL65 - ZL65 - Automation for swing gates Front Gates Front Gates...
- Page 15 TITLE COMMISSIONING VIA APP Set the Opening Delay M1 Set the safety inputs (please Select Calibrating Travel. and Closing Delay M2 to the refer to section 12 for desired value (secs). Select options). Select Next. Next. When the gate has successfully Select Add.
-
Page 16: Commissioning Via App
COMMISSIONING VIA APP Once it has been accepted on Select the back button to If you select ADD via QR Once the QR code has been the control panel It will display return to the main menu. Code, the app will open the scanned, enter a Name and the above screen. - Page 17 TITLE COMMISSIONING VIA APP transfer to customer name@mycustomer.co.uk name@mycustomer.co.uk Firstname Lastname To transfer to a customer, Select Transfer site Enter customer details you Select confi rm. The customer select the 3 dots. wish to transfer to. will get an email asking to confi rm the account.
-
Page 18: Commissioning Via Panel
Safety inputs should now be configured and the gate force tested as required. Please refer to the full manual to complete the commissioning. Should the gates not operate as suggested above, call CAME helpline 0115 921 0430 for technical support. - Page 19 Remove a transmitter button – Choose the type of radio coding for the transmitters = All decoding (default) = Rolling code = TW key block Should the transmitter not operate as suggested above, call CAME helpline 0115 921 0430 for technical support.
-
Page 20: Safety Options
TITLE SAFETY options SAFETY INPUTS FUNCTIONS > CX Input, CY Input REOPENING DURING CLOSING • When the automation is in its closing cycle and the safety circuit is triggered the automation will stop and reverse its motion until it reaches its fully open position again. -
Page 21: Replacing The Sim Card
replacing the sim card A third party SIM card may be used, for example, if an existing SIM card is available or the current SIM data contract expires. To insert a SIM card please do the following: With the power switched to the control panel, remove the RGSM casing, slide out the existing SIM card and fi t the replacement SIM card into the slot. -
Page 22: Optional Accessories
optional ACCESSORIES Code(s) Description RADIO KEYPAD SELECTORS 806SL-0170 SELT1W4G - Surface-mounted, 433.92 MHz radio-frequency keypad selector, 12-keys, with blue backlighting. 25 savable codes and password to access the programming mode. Settable in Rolling Code or Fixed Code mode. RAL7024 Grey colour. 806SL-0180 SELT1W8G - Surface-mounted, 868.35 MHz radio-frequency keypad selector, 12-keys, with blue backlighting. - Page 23 Black anodised aluminium post. H = 500mm 001DIRCG Silver RAL9006, PVC post. H = 500mm CAME KEY 806SA-0110 WiFi internet gateway. Communicate directly with your smartphone or tablet, allowing you to manage the configuration of your device with no need for an internet connection.
- Page 24 User to submit a contractual offer, which will be submitted by password. fi lling in the Form. Came reserves the right to accept or reject said offer. Except in the event that a third party violates the Came computer systems, the User shall be exclusively responsible for maintaining the 4.3 The Contract will be considered concluded at the moment in which the...
- Page 25 Italy, by the Italian conditions, Came will not be in any way liable for the failed or faulty Legislative Decree dated 6 September 2005, no. 206, “Consumer provision of the Service, nor will it be liable for any loss, damage or Code”, with specifi...
- Page 26 Court of Treviso (Italy). CAMECONNECT 8.3 Came reserves the right to make changes to the Terms of Use at any 3.1 CameConnect has the features described in detail in the User Manual. time, publicising them on this page. In the event of a failure to accept the changes made to the Terms of Use, the Installer may withdraw 3.2 The features of the Software and CameConnect are subject to change...
- Page 27 TITLE TITLE terms and conditions General Terms and Conditions of 1NCE GmbH for M2M/IoT mobile communications services (version as of 07/2018) 3.1 lit. c) of these GTC. 1NCE expressly points out that the type and Scope of application scope of such services of the respective mobile network operators, 1.1 The following General Terms and Conditions (hereinafter referred to as in particular also the respective available transmission technologies “GTC”) shall govern any and all contracts relating to the provision of...
- Page 28 TITLE terms and conditions of receipt of the relevant Chip Cards by the Customer. Liability for Section 3.3 sentence 2 of these GTC shall be determined by the price damages due to defects is limited in accordance with the provisions of list of 1NCE valid at the time of this purchase.
- Page 29 TITLE terms and conditions 10.2 The Parties also undertake to treat all other confi dential information Liability of the other Party that the receiving Party becomes aware of in Any liability of 1NCE for damages and/or reimbursement of expenses connection with the contractual relationship as strictly confi dential arising from or in connection with the contractual relationship between and not to disclose such information to any third party for an unlimited 1NCE and the Customer shall be subject to the following limitations:...
- Page 30 TITLE notes...
- Page 31 TITLE notes...
- Page 32 YOU MAY NOT EVEN PARTIALLY REPRODUCE THIS DOCUMENT CAME RESERVES THE RIGHT TO MAKE ANY CHANGES TO THIS DOCUMENT AT ANY TIME THE DATA AND INFORMATION SHOWN IN THIS CATALOGUE ARE SUBJECT TO CHANGE WITHOUT OBLIGATION TO GIVE PRIOR NOTICE BY CAME S.P.A, E&OE CAME S.p.A.