Installation; Installing The Filter; Operation; Understanding The Air Quality Light Ring - Bosch Air 6000 Installation Instructions Manual

3

Installation

3.1

Installing the filter

▶ Pull the back cover and remove it from the appliance.
▶ Pull the filter from the appliance.
▶ Remove the plastic cover of the air purification filter.
▶ Insert the filter back into the appliance.
▶ Reattach the back cover.
[Figure 5 Removing the back cover]
[Figure 6 Removing the plastic cover]
[Figure 7 Inserting the filter and reattaching the back cover]
4

Operation

4.1

Understanding the air quality light ring

The light ring indicates the air quality. It lights up all colours in sequence,
when the air purifier is switched on. After approximately 30 seconds, the
particle sensor selects the color that corresponds to the surrounding air
quality of airborne particles, according to table 2.
PM2.5
PM2.5 refers to ultra-fine airborne particle pollutants smaller than 2.5
micrometers. Most of the indoor air pollutants fall under PM2.5 like:
tobacco smoke, cooking and burning candles, some airborne bacteria
and the smallest mold spores, pet allergen and dust mite allergen
particles also fall under PM2.5.
The air quality sensor scans the air continuously to detect the ultra-fine
particles. This information is reported continuously in both the digital
display and the light ring, providing real-time PM2.5 feedback.
Air quality light color Air quality level
Blue Good
Purple Ok
Orange Poor
Red Bad
Table 17 Air quality light colors and PM2.5 levels
4.2

Switching ON/OFF

▶ Insert the plug of the air purifier in the power socket.
▶ Touch to switch on the air purifier.
▶ Press the button again, to switch off the air purifier.
Note
• For optimum purification performance, close the doors and the
windows.
• Keep curtains away from the air inlet or air outlet.
• The air purifier will operate in Auto mode by default.
4.3

Changing the mode setting

Auto-mode
• In Auto-mode, the air quality is registered in real-time, and the
appliance automatically adjusts the fan speed in accordance to the
ambient air quality.
Manual mode
• In Manual mode, it is possible to set the fan speed (between Speed 1
and Speed 3). Press the
Quiet mode
• In Quiet mode, the air purifier operates quietly at a low speed and all
the lights are dimmed.
Air 6000 – 6721848696 (2023/07)
PM2.5 level
0-12
13-35
36-55
>56
button to change to the desired speed.
Timer mode
• In Timer mode, it is possible to set the timer (between 1 and 12
hours) for the equipment shut off.
5

Cleaning and maintenance

5.1

Cleaning the housing of the air purifier

Regularly clean the inside and outside of the housing of the air purifier to
prevent dust from collecting.
▶ Wipe the surface with a damp cloth.
▶ Use a soft, dry cloth to clean both the interior and exterior of the air
purifier and the air outlet.
5.2

Cleaning the particle sensor

Note:
• If the air purifier is used in a dusty environment, it may need to be
cleaned more often.
• If the humidity level in the room is very high, condensation may
develop on the air quality sensor and the air quality light may indicate
a poorer quality even though the air quality is good.If this occurs,
clean the air quality sensor.
Clean the air quality sensor every month for optimal functioning of the
appliance.
▶ Switch off the air purifier and unplug from the power socket.
▶ Pull the back cover and remove it from the appliance.
▶ Clean the particle sensor with a damp cotton swab.
▶ Dry all parts with a dry cotton swab.
▶ Reattach the cover.
[Figure 8 Cleaning the air quality sensor]
5.3

Cleaning the filter

CAUTION
Wear a mask and gloves when cleaning the filter surface and/or replacing
the filter.
▶ Switch off the air purifier and unplug it from the power socket.
▶ Pull the back cover and remove it from the appliance.
▶ Pull the filter from the appliance.
▶ Clean the surface of the filter with a vacuum cleaner.
▶ Insert the filter back into the appliance.
▶ Reattach the cover.
▶ Insert the plug of the air purifier in the power socket.
▶ Touch the power button
▶ Touch the filter status check/reset button
▶ Wash your hands after cleaning the filter.
[Figure 5
Removing the back cover]
[Figure 9
Removing and cleaning the filter]
Installation
to switch on the appliance.
.
35