Table of Contents
Advertisement
Quick Links
CentronicPLUS
EC541A PLUS
Assembly and Operating Instructions
en
1-channel hand-held transmitter, bidirectional
Important information for:
• Fitters / • Electricians / • Users
Please forward accordingly!
These instructions must be kept safe for future reference.
4036 630 297 0 23/11/2022
Becker-Antriebe GmbH
Friedrich-Ebert-Straße 2-4
35764 Sinn/Germany
www.becker-antriebe.com
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Becker CentronicPLUS EC541A PLUS
Summary of Contents for Becker CentronicPLUS EC541A PLUS
- Page 1 Assembly and Operating Instructions 1-channel hand-held transmitter, bidirectional Important information for: • Fitters / • Electricians / • Users Please forward accordingly! These instructions must be kept safe for future reference. 4036 630 297 0 23/11/2022 Becker-Antriebe GmbH Friedrich-Ebert-Straße 2-4 35764 Sinn/Germany www.becker-antriebe.com...
-
Page 2: Table Of Contents
Table of contents General .................... 3 Licensing information for open source software.......... 3 Warranty .................... 4 Safety instructions ................... 4 Intended use ................... 5 Explanation of displays and buttons ............ 6 Explanation of functions ................ 6 Programming transmitter................ 9 Restoring the factory settings of the hand-held transmitter...... 10 Installing the wall bracket................. 11 Changing batteries.................. 11 Cleaning.................... 12... -
Page 3: General
Written request for the licence texts: Becker-Antriebe will, on request, provide the licence texts for the licensed software being used at cost price, either on a USB stick or a similar data car- rier. Please send an email to the following email address for more information: licenses@becker‑antriebe.com... -
Page 4: Warranty
Warranty Structural modifications and incorrect installation which are not in accordance with these and our other instructions can result in serious injuries, e.g., crush- ing of limbs. Therefore, structural modifications may only be carried out with our prior approval and strictly in accordance with our instructions, particularly the information contained in these Assembly and Operating Instructions. -
Page 5: Intended Use
Intended use The transmitter described in these instructions must only be used indoors for the operation of radio drives and radio control units that are compatible with the CentronicPlus. • Please note that radio-controlled systems may not be used in areas with a high risk of interference (e.g. -
Page 6: Explanation Of Displays And Buttons
Explanation of displays and buttons 1. LED ring function button button 6. Battery compartment button (STOP) programming button button Explanation of functions LED ring Display of: • Confirmations from receiver • manual / automatic • Threshold / dimming values • Battery status •... - Page 7 Keypad , , • Drive commands • Memory function • Intermediate position I + II Function button • Identification of the transmitter Programming button • Environment scan, as well as selection and programming of receivers • Add and remove receivers to/from the installation •...
- Page 8 Identification of the hand-held transmitter A colour can be assigned to the LED ring of the hand-held transmitter by pressing the function button to make the device easier to identify. The stored colour can be displayed by briefly pressing the function button. If the function button is pressed for longer than 3 seconds, the LED ring flashes briefly.
-
Page 9: Programming Transmitter
Installation key All of the devices operating within an installation must have the same installa- tion key in order to communicate with one another. This key is created on ini- tial commissioning, and is then transmitted to the additional added devices. The installation key is only known to the programmed devices, and cannot be read off. -
Page 10: Restoring The Factory Settings Of The Hand-Held Transmitter
Restoring the factory settings of the hand-held transmitter When the factory settings of the transmitter are restored, the settings in the receiver, such as run times, thresholds, intermediate positions, etc. as applicable, are not taken into account. Open the cover of the battery compartment and take out the batteries. -
Page 11: Installing The Wall Bracket
Installing the wall bracket • Before installation in the de- sired installation position, check that the transmitter and receiver are functioning prop- Wall bracket erly. • Use two suitable screws to fix the bracket to the wall. Wall bracket Unlocking mechanism mounting plate Changing batteries You will find the appropriate battery type in the "Technical... -
Page 12: Cleaning
Cleaning Only clean the device with a suitable cloth. Do not use aggressive cleaning agents that may damage the surface. Disposal The crossed-out bin symbol on the product indicates that the device is subject to mandatory disposal separate from household waste. This product must be handed over to a collection point for electrical and electronic equipment at the end of its service life. -
Page 13: What To Do If
What to do if...? Problem Remedy Tubular drive/receiver is not re- Insert new batteries into the hand- sponding. held transmitter. Insert batteries into the hand-held transmitter correctly. Reduce distance from receiver. Program transmitter. Check the receiver. LED ring flashes yellow or red 4 Insert new batteries into the trans- times.
Need help?
Do you have a question about the CentronicPLUS EC541A PLUS and is the answer not in the manual?
Questions and answers