USER'S MANUAL VERSION Version Date August, 2023 SAFETY REQUIREMENTS * The security can be compromised if not applied the instructions in this manual. * Use this instrument under the specified environmental conditions. * The user is not allowed to perform changes inside the equipment. Any change on the equipment mustbe done exclusively by specialized staff.
1. Product Introduction 1.1 Overview TBS8030T 1U 4k@60fps HDMI Encoder easily converts 4K UHD HDMI Video to IP stream in UDP/RTP protocol. It is equipped with 4/8/12/16 HDMI 2.0 ports and supports max 3840 x 2160P@60hz HDMI video inputs. The encoder supports both H.264 & H.265 Encoding, being able to compress channel's bit rate to 5-16M.
2. When the HDMI input is 3840x2160p_60hz or 50hz input, it can only be encoded into H.265 3840x2160p_60fps or 50fps.It is invalid even if manually setting the output in H.264. 3. TBS8030T doesn’t support to change video’s frame rate and resolution currently. 4. When the encoding output is in H.264/H.265 3840x2160p_60fps/50fps/30fps, please ensure that the decoder has sufficient decoding capacity.
2. Hardware description. ➢ TBS8030T has 4 different version: 4 HDMI input, 8 HDMI input, 12 HDMI input or 16 HDMI input. ➢ Eth0/TS Over IP port: DATA Ethernet port, DHCP to get IP. Supports 1000/100M. ➢ Eth1/Console port: Management Ethernet port, preset to a static IP “192.168.8.188”. Supports 1000M only.
3.Web GUI setting 3.1. GUI log in The default IP to access the GUI is “192.168.8.188”. The default login/password is: root/root. 3.2. Network setting: Eth0: This is data Ethernet port, for streaming purpose. The default is set to DHCP to get IP. Eth1: This is management Ethernet port, for web GUI control.
➢ Video Encode: For TBS8030T Encoder, the output resolution and frame rate both are not allowed to be changed. It keeps the same as the “Input”. So, there is not“Options” to set these 2 parameters on web GUI. For example: If the input video is 3840x2160_60hz, the output video will beencoded to 3840x2160@60fps.
Apply: Activate all the new configurations. 3.3.2 Streaming: TBS8030T supports UDP/RTP unicast or multicast output protocol. After configure output address and port, click “Apply”. If Encoder didn’t detect the input stream correctly, it will remind you streaming failed. Address: East Room, 3/F Bldg. B, Xinghong Industrial Park, Shuiku RD., Xixiang Town, Bao’an District, SZ, China, 518055...
➢ The output stream URL: HDMI 0, the URL will be: udp://@192.168.8.170:4050; HDMI 3, the URL will be udp://@239.255.6.9:4053; HDMI 5, the URL will be rtp://@239.255.7.8:4055. 3.3.3 HDMI State Indicate HDMI video and audio input information. If signal is not detected, it shows “gray” like HDMI 7: Address: East Room, 3/F Bldg.
It shows the Firmware version number. 4. Remote power off/Power on for Encoder. TBS8030T encoder supports remote power off/power on. To ensure proper functionality,please make sure the encoder is powered and the network is reachable.This function is achieved by cutting off a small part power supply of Encoder to power it off or power it on.
➢ Scan Encoder: # ./RK3568NetworkTool –c ➢ Power Encoder off: # ./RK3568NetworkTool -i 192.168.8.188 -p 5443 -E 0 ➢ Power Encoder on: # ./RK3568NetworkTool -i 192.168.8.188 -p 5443 -E 1 192.168.8.188 is the IP address of Encoder Ethernet 1 port (the management Ethernet port). 5.
the service required. ➢ Mail: support@tbsdtv.com or support@tbsiptv.com. 5.2Cleaning Recommendations CAUTION: To clean the cover, take care the instrument is disconnected. ➢ CAUTION: Do not use scented hydrocarbons or chlorized solvents. The cover should be cleaned by ➢ means of a light solution of detergent and water applied with a soft cloth. Dry thoroughly before using the system again.