Table of Contents
Advertisement
Quick Links
08/2023
Canadian Timber
Granby
Cabin Assembly Instructions
Requirements:
2 People (recommended)
Rubber Mallet
Carpenter's Level
Tape Measure
Cordless Drill
Phillips & Robertson Drill Bits
2" (51mm) hole saw
¼" (6mm) Nut Driver Bit
Step Ladder
Carpenter's Hammer
Utility Knife
It is highly recommended to view the assembly video prior to starting assembly!
View the assembly process
Manufactured by:
tel: 888-923-9813 | info@leisurecraft.com| web: www.leisurecraft.com
Advertisement
Table of Contents
Related Manuals for leisurecraft Canadian Timber Granby
Summary of Contents for leisurecraft Canadian Timber Granby
- Page 1 2” (51mm) hole saw ¼” (6mm) Nut Driver Bit Step Ladder Carpenter’s Hammer Utility Knife It is highly recommended to view the assembly video prior to starting assembly! View the assembly process Manufactured by: tel: 888-923-9813 | info@leisurecraft.com| web: www.leisurecraft.com...
-
Page 2: Parts List
603510 Algoma Black Metal Shingle 603511 Roll of M-Seal CT66WMANUAL Granby Cabin Sauna Manual VENT1 Sauna Vent 603020 Outside Sauna Door Handle (Small)- White Cedar 603021 Inside Sauna Door Handle (Large) - White Cedar tel: 888-923-9813 | info@leisurecraft.com| web: www.leisurecraft.com... - Page 3 Canadian Timber Granby Cabin Assembly Instructions Index Parts List Base Preparation Cabin Assembly Roof Installation Bench Installation Electric Heater Installation (Option) Care &Maintenance Warranty Manufactured by: tel: 888-923-9813 | info@leisurecraft.com| web: www.leisurecraft.com...
- Page 4 A solid base for your sauna is recommended and can be made from any of the following. Concrete Pad Wood Deck Crushed Stone Patio Stone/Paver Blocks It is recommended to build a base larger than required to provide a sitting area for cooling off during your sauna session Manufactured by: tel: 888-923-9813 | info@leisurecraft.com| web: www.leisurecraft.com...
-
Page 5: Cabin Assembly
Insert 3 – 2 ½” (64mm) screws into the end of each base stave. Repeat this process for all 7 supports. 2 supports on either end and the remaining 3 centered on “marks”. Manufactured by: tel: 888-923-9813 | info@leisurecraft.com| web: www.leisurecraft.com... - Page 6 Once it is even with the first stave, secure it using 2- 2 ½” (64mm) screws into the supports as in the previous step. Manufactured by: tel: 888-923-9813 | info@leisurecraft.com| web: www.leisurecraft.com...
- Page 7 Place 3 -3” (76mm) screws into each of the side supports. Locate the wall stave labelled “Door”. Fasten the front starter door stave with 2 - 3” (76mm) screws to secure it to the floor. Manufactured by: tel: 888-923-9813 | info@leisurecraft.com| web: www.leisurecraft.com...
- Page 8 Now place a full length stave at the rear of the sauna and tap the tongue and groove together to make sure it is tight and secure with a 5” (127mm) screw into the notch at either end. Manufactured by: tel: 888-923-9813 | info@leisurecraft.com| web: www.leisurecraft.com...
- Page 9 Place another full length stave at the rear of the sauna and tap the tongue and groove together to make sure it is tight and secure with a 5” (127mm) screw into the notch at either end. Manufactured by: tel: 888-923-9813 | info@leisurecraft.com| web: www.leisurecraft.com...
- Page 10 Place the angled side wall staves ensuring the angle is sloped down towards the outside of the sauna. Secure with a 5” (127mm) screw in each notch. Manufactured by: tel: 888-923-9813 | info@leisurecraft.com| web: www.leisurecraft.com...
- Page 11 Secure each end with a 3” (76mm) screw on each side of each gable. Now fasten the bottom wall stave on every side of the sauna to the floor staves using 2 ½” (64mm) screws. (3 per side) Manufactured by: tel: 888-923-9813 | info@leisurecraft.com| web: www.leisurecraft.com...
-
Page 12: Roof Assembly
Use the thinner roof stave to finish the roof on this side. Secure to the gable ends with 2 – 3” (76mm)screws and 5 – 5” (127mm) screws into the previous stave. Repeat the process for the other side of the roof. Manufactured by: tel: 888-923-9813 | info@leisurecraft.com| web: www.leisurecraft.com... - Page 13 Screw the shingle to the roof at the bottom of each ridge. Manufactured by: tel: 888-923-9813 | info@leisurecraft.com| web: www.leisurecraft.com...
- Page 14 Place the roof ridge cap under the front and back trim pieces. Secure it on both sides with roofing screws in every other ridge. Manufactured by: tel: 888-923-9813 | info@leisurecraft.com| web: www.leisurecraft.com...
- Page 15 For the side with the door, use the middle hinge on the top and bottom with the 3 screw centered between them. Manufactured by: tel: 888-923-9813 | info@leisurecraft.com| web: www.leisurecraft.com...
-
Page 16: Bench Assembly
Ensure bench support is square and secure with 2” (51mm) screws from the bench into the support. Again, place the screws into between the bench slats to make them less visible. Manufactured by: tel: 888-923-9813 | info@leisurecraft.com| web: www.leisurecraft.com... - Page 17 Canadian Timber Granby Cabin Assembly Instructions Bench Assembly Repeat the process for the bottom bench. Screw the bench supports to the floor and back wall using 2” (51mm) screws. Manufactured by: tel: 888-923-9813 | info@leisurecraft.com| web: www.leisurecraft.com...
-
Page 18: Electric Heater Installation
Transfer the measurements to the back wall of sauna. Ensure the heater will be centered between the benches. Install the two ¼" x 1 ½" (6mm x 38mm) hex head lag screws (supplied with the heater) into the holes. Manufactured by: tel: 888-923-9813 | info@leisurecraft.com| web: www.leisurecraft.com... - Page 19 (2) – 1 ½” (38mm) screws per side. Repeat for the bottom heater guard support. Place 2- 2 ½” (64mm) screws into the pre-drilled holes on either side of heater guard to prepare for mounting. Manufactured by: tel: 888-923-9813 | info@leisurecraft.com| web: www.leisurecraft.com...
- Page 20 “cures” the woodwork. All wiring should be installed according to the heater manufacturers instructions and by a • licensed electrician. • Do NOT use a G.F.I breaker Manufactured by: tel: 888-923-9813 | info@leisurecraft.com| web: www.leisurecraft.com...
-
Page 21: Care And Maintenance
This natural weathering will not harm the wood or impair the sauna’s performance. If you wish to retain the natural color of your Dundalk Leisurecraft Sauna, there are many cedar stains on the market and almost as many opinions as to which is best. -
Page 22: Warranty
This warranty is a parts only warranty and any service or labor costs would not be considered as part of the 3 year warranty. Purchaser Name: ________________________ Date: _______________ Purchased From: ________________________ Manufactured by: tel: 888-923-9813 | info@leisurecraft.com| web: www.leisurecraft.com...