Siemens REV24 Series Operating Instructions page 2

Select operating mode
Press the operating mode button to select one of 5 modes.
Operating modes with time program
The controller offers both time programs Automatic
Do you feel too warm / too cold ?
Press or to set the temperature. The setting is temporary and active only until the
next time the controller activates a change.
Note: To set your own programs, see: "Enter customized temperatures and switching times".
Continuous operating modes
The controller offers continuous operating modes "Continuous comfort mode"
"Continuous energy saving mode" and protection mode (frost or overheating)
Do you feel too warm / too cold?
Press or to set a continuous temperature.
Enter time and date
Slider in position 1 (time setting): Press
Slider in position 2 (date: Day/month/year): Press
RUN Reset the slider to the RUN position.
Note: You do not need to enter time and date when DCF77 receiver for the time signal
from Frankfurt (Germany) is equipped. The time display shows PASS.
Enter customized temperatures and switching times
The controller has three different switching patterns that you can allocate to the weekday blocks
1-5, the weekend block 6-7, or to the individual days 1...7.
Proceed as follows:
Select operating mode
Slider in position 3 (weekdays
Press or to select the block (weekdays, weekend) or individual day.
Note: Making changes to individual days destroys the corresponding block.
You can only restore a destroyed block by Reset the controller.
Slider in position 4 (number of comfort phases): Press
number of comfort phases.
Slider in position 5 (start time comfort phase 1): Press
start time.
Slider in position 6 (temperature comfort phase 1): Press
temperature.
Slider in position 7 (end time comfort phase 1): Press
end time.
, ,
Slider positions 8...10 (comfort phase 2) and slider positions 11...13
(comfort phase 3): Same procedure as above for comfort phase 1.
, ,
Slider in position 14 (energy saving temperature in time switch programs
Automatic and Exception day): Press
Note: The energy saving temperature is valid Monday through Sunday.
It does not depend on operating mode "Continuous energy saving".
Move the slider to RUN position and close the cover.
RUN
Notes (e.g. individual settings):
B2205en
and Exception day
,
or to set the time.
or to set the date.
or .
, weekend , individual days
or to set the
or to set the
or
or to set the
or to set the temperature.
Enter holidays or absence
You can enter start, temperature and end of your holidays. The controller switches to the set holiday
temperature at the start of the holidays and back to the preset operating mode at the end of the holidays.
During holiday mode, symbol
Proceed as follows:
.
Slider in position 15 (start of absence): Press
Slider in position 16 (temperature during absence): Press
effective during the holidays.
Slider in position 17 (end of absence): Press
Move the slider back to RUN. Symbol
RUN
To quit holiday mode prematurely, press
. Enter temperature for active remote control
With remote control, you are free to select the temperature. Activating remote control immediately
enables control to the remote operating temperature regardless of the current operating mode. After you
switch off remote control, the device returns to the set operating mode.
Symbol flashes with active remote control
Proceed as follows:
Slider in position 18 (temperature for active remote control): Press
temperature for active remote control.
Move the slider back to RUN.
RUN
Reset to factory settings
Press and
and time settings are reset to default values.
The clocks starts at 12:00.
Caution: All customized settings are lost !
Factory settings: Heating
, , ,
):
,
,
Factory settings: Switching times
Comfort phases
1.
to set the 2.
3.
Activate Party mode
You can activate Party mode only in operating modes
to any selectable temperature for any selectable time.
In Party mode, symbol
Proceed as follows:
1. Press
Press
2.
The entry is accepted after 20 seconds or when you press
3. Press
Party mode ends automatically after the Party duration ends or when you press
4.
or
29.03.2018
flashes and the end of the holidays is displayed.
or
or
appears to the left of symbol
, , ,
.
together with the operating mode button
Factory settings: Cooling
20 °C
16 °C
8 °C
12 °C
P1 P2 P3
07:00 23:00 PASS
06:00 08:00 17:00
06:00 08:00 11:00
and
is displayed along with the end of Party mode.
for 3 seconds.
or to set the duration for Party mode. Party mode can last max. 9 hours.
or to set the temperature.
.
to set the start of the holidays (date).
or to set the temperature
to set the end of the holidays (date).
.
or move the slider.
or to set the
for 3 seconds. All temperature
24 °C
, , ,
28 °C
,
35 °C
30 °C
,
P4 P5 P6
PASS PASS PASS
22:00 PASS PASS
13:00 17:00 22:00
. In Party mode, the device controls
.
Siemens, Building Technologies