Self-learning room temperature controller receiver (17 pages)
Summary of Contents for Siemens REV34 Series
Page 1
7-day REV34.. room temperature controller Heating applications ∂ Mains-independent, battery-operated room temperature controller featuring user-friendly operation, easy-to-read display and large numbers. ∂ 3-position controller with PI mode and optimum start control. ∂ Possibility to adapt volume and control gain. ∂ Operating mode selection: - 7-day automatic mode with max.
Page 2
1.5 V alkaline batteries, type AA. The base with terminal block provides lots of space to connect the wires. Display and operating elements 2 / 15 Siemens Room temperature controller REV34.. CE1N2208en Building Technologies 2017-11-15...
Page 3
The unit first displays queued error messages followed by important information (e.g. time switch programs, etc.). Plus button Increase values, set time, or make a selection. 3 / 15 Siemens Room temperature controller REV34.. CE1N2208en Building Technologies 2017-11-15...
Page 4
Start of absence / holiday Temperature setpoint during absence / holiday End of absence / holiday Temperature setpoint at active remote control Slider position RUN allows for closing the cover 4 / 15 Siemens Room temperature controller REV34.. CE1N2208en Building Technologies 2017-11-15...
Page 5
6…7. As a result, you need to adapt the switching times and room temperatures only once for each block. Switching pattern Blocks You can also enter individual days … 5 / 15 Siemens Room temperature controller REV34.. CE1N2208en Building Technologies 2017-11-15...
Page 6
Proceed as follows to enter your settings: Set slider to temperature position for active remote control: Press set the desired temperature for active remote control. RUN Return the slider to position RUN. 6 / 15 Siemens Room temperature controller REV34.. CE1N2208en Building Technologies 2017-11-15...
Page 7
½ h/°C For medium controlled systems. DIP switches 4 OFF and 5 OFF: OFF Off, no effect (factory setting). Press the DIP switch reset button to save the settings. 7 / 15 Siemens Room temperature controller REV34.. CE1N2208en Building Technologies 2017-11-15...
Page 8
Frankfurt, Germany. Synchronization takes max. 10 minutes. Synchronization restarts each time you press the button or move the program selection slider from the RUN position during these 10 minutes. Siemens recommends to set the desired settings 8 / 15 Siemens Room temperature controller REV34..
Page 9
Frankfurt, atmospheric conditions as well as the on reception location where the REV..DC is installed. Siemens cannot guarantee that the REV..DC can receive the time signal from Frankfurt at any time and any place.
Page 10
CLOSED. Driving the actuator to the fully CLOSED position takes max. 150 Important: seconds. After a reset, reinsert the controller in the base within 30 seconds. 10 / 15 Siemens Room temperature controller REV34.. CE1N2208en Building Technologies 2017-11-15...
(as needed), date, comfort phases, etc.. Notes This is a software class A controller designed for use at a normal degree of pollution. 11 / 15 Siemens Room temperature controller REV34.. CE1N2208en Building Technologies...
Page 12
II as per EN 60 730-1 NTC 10 kς ς1 % at 25 °C Sensing element Measuring range 0…50 °C Time constant Max. 10 min Setpoint setting ranges All temperature settings 3…35 °C 12 / 15 Siemens Room temperature controller REV34.. CE1N2208en Building Technologies 2017-11-15...
Page 13
0.32 kg Color Housing RAL9003 signal white Base RAL7038 gray Size Housing with base 90 x 134.5 x 30 mm *) The documents can be downloaded from http://siemens.com/bt/download 13 / 15 Siemens Room temperature controller REV34.. CE1N2208en Building Technologies 2017-11-15...