Siemens REV15 series Operating Instructions

Operating instructions
REV15... - the temperature controller that allows you to set the ideal room temperature at the time you want. There
are several switching patterns available that can be set to suit your specific needs. You can either rely on the
factory settings or make settings taillored to your personal needs.
Normal temperature
Display
Economy temperature
Holiday mode
Standby
Weekday (1=Monday / 7=Sunday)
Room temperature (measured)
Time of day
Switching pattern
with time cursor
Settings
D ay
Time
Weekday
D ay
Switching times A1... A6
A1 A2 A3 A4 A5 A6
Switching times B1... B2
B1 B2
Normal temperature
Economy temperature
Changing the
Holiday period
setting values
Auto
Operating mode
Run
Commissioning with quick startup
The controller is supplied with factory-set switching patterns, switching times and temperatures. To commission it,
proceed as follows:
Remove the black transit tabs from the two batteries. Check to see if the battery holder is in its correct
1.5V 'AA'
1.5V 'AA' position. The controller switches itself on.
Move the setting slider to this position. Press buttons
D ay
Move the setting slider to this position. Press buttons
(1 = Monday...7 = Sunday).
Auto Move the setting slider back to position on the right, because only that position allows you to close the
cover.
Run
Select the required operating mode with the operating mode selector.
Fold up operating instructions again, place them back into the cover and close the cover again.
Landis & Staefa REV15...
Heating on
Current 24-hour mode
A B
Replace batteries
Remote operation active
(if connected)
1 2 3 4 5 6 7
°C
A B
0 6 12 18 24
Auto
Auto A/B
A1 A2 A3 A4 A5 A6 B1 B2 Run
1.5V 'AA'
1.5V 'AA'
Setting slider
2225Z11E
to set the correct time of day.
to set the correct weekday.
Do you want to use automatic operation?
Operation
Warmer/colder setting
valid up to the next
switching point
(increments of 0.2 ºC,
The display shows the respective letter A or B.
± 4 ºC max.)
Do you require continuous normal
Change
temperature?
between normal and
economy mode up to the
next switching point
Operating mode
selector
Do you require continuous economy
Weekly mode with
temperature?
3 heating periods (A 1-5) /
1 heating period (B 6-7)
24-hour mode A
A
with 3 heating periods
B
24-hour mode B
with 1 heating period
Do you require continuous standby with frost
Continuous protection?
normal temperature
Continuous
economy temperature
Standby
with frost protection
Do you feel too warm or too cold?
If that is the case, set the operating mode
selector to one of the following positions:
You use the weekly setting with automatic
Auto A/B
changeover from three heating periods on
weekdays (A 1-5) to one heating period on
weekends (B 6-7).
You use the 24-hour setting A with three
A
heating periods.
You use the 24-hour setting B with one
B
heating period.
Move the operating mode selector to «Normal
temperature». This ensures continuous
heating to the normal temperature. The
display shows .
Move the operating mode selector to
«Economy temperature». This ensures
continuous heating to the economy
temperature. The display shows
Move the operating mode selector to
«Standby». In that case, heating is provided
only when the room temperature falls below
the preset frost protection limit (5 °C). The
display shows .
By pressing these buttons, you increase or
°C
decrease the actual room temperature in
increments of 0.2 °C by a maximum of ± 4°C.
The display first shows the newly selected
temperature and then the actual value again.
These changes are valid only up to the
next switching point. If, as a result of the
factory settings, you always feel either too
warm or too cold, you should readjust the
temperature or to suit your needs.
.