General Warnings; User Instruction - Kemper 1810 Manual

1810
3. To use this appliance in total safety implies observing some basic safety
measures, such as: never use the appliance with wet hands or feet, never
expose the appliance to moisture or water, never leave the appliance exposed
to atmospheric agents, never disconnect the plug by pulling the power cord
or the appliance itself.
4. After finishing the work, turn off the product and leave the soldering iron
cool in the air; never put it under water in order to avoid electric shocks. Do
not touch metal parts of the soldering iron (tips or resistances) when it is on,
with your hands or other parts of the body. High temperatures can cause
severe burns.
5. Do not carry out any cleaning or maintenance without first disconnecting
the plug from the power supply.
6. If the power cord is damaged, it must be replaced by the manufacturer or
its service agent or a similarly qualified person in order to avoid any risks.

GENERAL WARNINGS

Before using the tool, control its integrity, if there are any defective parts, or it has other conditions, which could
negatively influence its functions and safety. Remove all the packaging material and make sure that the appliance
is in good condition. If you have any doubt, do not use the appliance and contact our After-Sales Service. Keep
the packaging material (staples, nylon bags, etc.) out of the reach of children. Before plugging the soldering iron
into a socket, check whether your voltage corresponds to the rating label of the appliance. This appliance must
be connected to an approved mains socket that complies with the safety regulations on electrical systems for civil
purposes. The electrical system must be specific for the appliance rated voltage. Never cover the appliance, as
this could cause risk of overheating.
Do not leave the soldering iron on, if you do not use it; it causes an early oxidation reaching over-temperatures
which could compromise the duration of the resistances.
The appliance must be used only for its intended use, which is soldering iron. Any other use than its intended
purpose shall be deemed to be improper and hazardous. The manufacturer shall not be held responsible for
damages derived from misuse of this appliance.
Always unplug the appliance before performing any maintenance and whether it is not used for long periods of
time. Before inserting or removing the tips, unplug the appliance. Never connect the power cord to extensions or
triple plugs. Do not pull or damage the power cord. If the appliance does not work properly, immediately turn off
the appliance and disconnect it from the mains socket. For repairs, contact a technical support centre authorised
by the manufacturer, and require that original spare parts be used. Using parts that do not conform to the product
may seriously compromise its correct operation. This tool can set fire to different materials, make a proof on a
discarded material before use.
If the power cord is damaged, it must be replaced by the manufacturer or the manufacturer's technical support
service, or by an adequately qualified technician so as to prevent any risks.
Disorder and scarce lighting could cause incidents. Keep the working area always clean and well-lighted
The possible exhalations coming from the material on which you are working can be dangerous. Ask for
information about toxicity of the used materials and work in a well-ventilated area. Keep away your hands from
the hot tips and working area. The heat can be transmitted by the piece. Protect the working surface and materials
against damages caused by heat. Non-skilled users shall not to carry out works or repairs where a specific training
is necessary (for example the repair of electric/electronic appliances). The appliance has dangerous components
that must be kept out of the reach of children. The power cord must never be in contact with the hot surfaces of
the soldering iron. This tool is not a toy.
ATTENTION: Always place the stand on a flat and regular surface. If necessary, use safety glasses.

USER INSTRUCTION

1. Loosen the screws on the blade holders with the hex key (supplied in the box).
2. Slide the blade until it easily dovetails under its supports.
3. Tighten the screws (do not over-tighten).
4. Insert the power cord plug into a suitable volt, grounded, electrical outlet.
5. The temperature control knob has 16 possible positions. The smaller the ridges on the knob are, the lower the
power setting is.
6. Switching on: press the button and hold for less than 20 seconds.
7. Switching off: release the button for 30 sec minimum.
8. Unplug the appliance and let the blade cool down before store it.
DT ISTR_1810_4/2012_ REV.5_03/2018 6/28