General Warnings; User Instruction; Instructions For Disposal - Kemper 170020 User Instruction

Hide thumbs Also See for 170020:

Manual (21 pages)

Table Of Contents

Table of Contents

Available languages

soldering iron cool in the air; never put it under water in order to avoid electric

shocks. Do not touch metal parts of the soldering iron (tips or resistances) when

it is on, with your hands or other parts of the body. High temperatures can cause

severe burns. This tool can set fire to different materials, make a proof on a

discarded material before use.

If the power cord is damaged, it must be replaced by the manufacturer or the

manufacturer's technical support service, or by an adequately qualified

technician so as to prevent any risks. The power cord must never be in contact

with the hot surfaces of the soldering iron. This tool is not a toy.

ATTENTION: Always place the stand on a flat and regular surface.

Before using the tool, control its integrity, if there are any defective parts, or it has other conditions, which could negatively influence

its functions and safety. Remove all the packaging material and make sure that the appliance is in good condition. If you have any

doubt, do not use the appliance and contact our After-Sales Service. Keep the packaging material (staples, nylon bags, etc.) out of

the reach of children. Before plugging the soldering iron into a socket, check whether your voltage corresponds to the rating label

of the appliance. This appliance must be connected to an approved mains socket that complies with the safety regulations on

electrical systems for civil purposes. The electrical system must be specific for the appliance rated voltage. Never cover the

appliance, as this could cause risk of overheating. Do not leave the soldering iron on, if you do not use it; it causes an early oxidation

reaching over-temperatures which could compromise the duration of the resistances.

The appliance must be used only for its intended use, that is soldering iron. Any other use than its intended purpose shall be deemed

to be improper and hazardous. The manufacturer shall not be held responsible for damages derived from misuse of this appliance.

Always unplug the appliance before performing any maintenance and whether it is not used for long periods of time. Before inserting

or removing the tips, unplug the appliance. Never connect the power cord to extensions or triple plugs. Do not pull or damage the

power cord

If the appliance does not work properly, immediately turn off the appliance and disconnect it from the mains socket. For repairs,

contact a technical support centre authorised by the manufacturer, and require that original spare parts be used. Using parts that do

not conform to the product may seriously compromise its correct operation.

Disorder and scarce lighting could cause incidents. Keep the working area always clean and well-lighted

The possible exhalations coming from the material on which you are working can be dangerous. Ask for information about toxicity

of the used materials and work in a well-ventilated area. Keep away your hands from the hot tips and working area. The heat can be

transmitted by the piece. Protect the working surface and materials against damages caused by heat. Non-skilled users shall not to

carry out works or repairs where a specific training is necessary (for example the repair of electric/electronic appliances). The

appliance has dangerous components that must be kept out of the reach of children. If necessary, use safety glasses.

It is recommended to use core flux tin rods or soldering grease.

Plug in the soldering iron and after about three minutes the point will be sufficiently hot to melt solder. Before first use, it is necessary

to cover the point with a coat of tin. To replace the soldering point, disconnect from mains supply and allow to cool. Loosen the two

fixing screws and pull off the point. Insert the new point and tighten the screws.

Disposal of this product shall be governed by the European Community Directive 2012/19/UE on Waste Electrical and Electronic Equipment

(WEEE). According to this regulation, the consumer has the obligation NOT to dispose of this product as household waste but through separate

channels of collection (WEEE). Electrical appliance should not be disposed together with household waste. This symbol indicates the

consumer's duty to dispose of this article as WEEE and NOT as household waste. Thank you for addressing to the collection points

provided recycling electrical appliance. Please contact local authorities or the seller for any advice on how to recycle. Please recycle the

packaging in designated collection points. Improper disposal of the product by the consumer involves the application of administrative

sanctions provided by law.

Wir danken Ihnen für den Kauf eines unserer Produkte. Es wird geraten, diese Gebrauchsanweisung aufmerksam zu lesen: Sie

enthält wichtige Informationen über die Sicherheitsbestimmungen beim Gebrauch und der Instandhaltung des Geräts. Es wird

empfohlen, dieses Dokument aufzubewahren, um es in Zukunft zu Rate ziehen zu können.

Das Gerät darf von Kindern ab dem Alter von 8 Jahren und von Personen mit

verminderten körperlichen, sinnlichen oder geistigen Fähigkeiten oder ohne

Erfahrung oder der notwendigen Kenntnis benutzt werden, sofern sie

beaufsichtigt werden oder nachdem diese Anweisungen hinsichtlich des

sicheren Gebrauchs des Geräts und des Verständnisses der mit diesem

verbundenen Gefahren erhalten haben. Kinder dürfen mit dem Gerät nicht

DT ISTR (170020-40-60-80-90-100) 10/07_REV. 12_02/2017