Setting Commands - Sony IPELA SNC-RZ25N User Manual

4 describes the case of "mib-2.system. sysContact.0".
This field is used to describe the information on
administrator of this camera. Nothing is set at the
factory.
5 describes the case of "mib-2.system. sysName.0".
This field is used to describe administration node of
this camera. Nothing is set at the factory.
6 describes the case of "mib-2.snmpEnable
AuthenTraps.0". This example shows when "1"
(enable) is set. With this setting, a trap occurs when
there is an Authentication failure. When "2"
(disable) is set, no Authentication failure trap
occurs.
7 describes the community name and the reading/
writing attributes. This example shows the
identification number "ID=1", the community
name public, and enables read from any IP address
(0.0.0.0).
8 describes the community name and the reading/
writing attributes, similarly to 7. This example
shows the identification number ID=2, the
community name "private", and enables "read/
write" by the SNMP request packet from the host
"192.168.0.101".
9 describes the host name to send a trap. This
example shows the identification number "ID=1",
the community name "public", and enables sending
of traps to the host having the IP address
"192.168.0.101".

2. Setting Commands

The unit supports the following setting commands of
SNMP.
<Method>
GET, POST
<Command>
http://ip_adr/snmpdconf/snmpdconf.cgi?
<parameter>=<value>&<parameter>=...&...
First, perform the settings of the following parameters.
1) sysLocation=<string>
Set the case of "mib-2.system.sysLocation.0" in the
<string> position. The maximum length of
<string> is 255 characters.
2) sysContact=<string>
Set the case of "mib-2.system.sysContact.0" in the
<string> position. The maximum length of
<string> is 255 characters.
3) sysName=<string>
Set the case of "mib-2.system.sysName.0" in the
<string> position. The maximum length of
<string> is 255 characters.
4) enaAuthTraps=<value>
Set the case value of "mib-2.snmp.snmp
EnableAuthenTraps.0" in the <string> position.
Type "1" (enable) or "2" (disable) in the <value>
position.
5) community=<ID>,<rwAttr>,
<communityName>,<IpAddressString>
Set the community name and the reading/writing
attributes. <ID> describes the setting identification
number (1 to 8), <rwAttr> describes a character
representing the reading/writing attribute ("r", "R",
"w or "W"), <communityName> describes the
community name to be set, and <IpAddressString>
describes the IP address of the host you allow
access (0.0.0.0 for any host).
Example: To allow reading/writing by any host in the
"private" community and having the ID number "2".
community=2,w,private,0.0.0.0
6) trap=<ID>,<communityName>,
<IpAddressString>
Set the host you want to send traps to. <ID>
describes the setting identification number (1 to 8),
<communityName> describes the community
name to send traps to, and <IpAddressString>
describes the IP address of the host to send traps to.
Example: To specify the destination of traps as the
private community and the ID number "1".
trap=1,public,192.168.0.101
7) delcommunity=<ID>
This parameter is used to delete the previous
community setting. <ID> describes the community
setting identification number (1 to 8).
8) deltrap=<ID>
This parameter is used to delete the previous setting
of the host to send traps to. <ID> describes the trap
setting identification number (1 to 8).
When you have finished changing the SNMP setting
information using the above parameters 1) to 8), check
the changed settings using an inquiry commands. If the
changed settings are OK, restart the SNMP using the
following CGI command.
SNMP restart command
<Method>
GET, POST
87
Using the SNMP