Steffes 2100 Series Install Manual

Steffes 2100 Series Install Manual

Plug-in room heater
Hide thumbs Also See for 2100 Series:

Advertisement

2100 SERIES INSTALL GUIDE
PLUG-IN ROOM HEATER
NOTE: Always transport the heater in an upright
position to avoid damage to internal
components and insulation materials.
1

PERSONAL SAFETY INSTRUCTIONS

SAFETY ALERT SYMBOLS
Three safety alert symbols are used to alert you to personal
safety instructions. They are:
Electrical (1)
Mechanical (2)
Fire (3)
SIGNAL WORDS
Signal words that appear next to safety alert symbols are:
DANGER
WARNING
CAUTION
IMPORTANT
NOTE
Carefully read and understand the instructions before you continue.
DANGER indicates a hazardous situation which, if not avoided, will result in death or serious injury.
WARNING indicates a hazardous situation which, if not avoided, could result in death or serious injury.
CAUTION indicates a hazardous situation which, if not avoided, could result in minor or moderate injury.
IMPORTANT
The equipment described herein is intended for installation by a qualified technician in compliance
with applicable local, state, and national codes and regulations.
Disclaimer: In compiling this manual, Steffes has used its best judgement based upon information
available, but disclaims any responsibility or liability for any errors or miscalculations contained
herein, or any revisions hereof, or which result, in whole or in part, from the use of this manual or any
revisions hereof.
2

SAFETY PRECAUTIONS

1. DO fully assemble the heater before energizing.
2. DO keep all explosive materials and/or flammable gases away from the heater.
3. DO maintain the placement and clearance requirements (Section 4).
4. DO keep items away from the discharge air grill area of the heater.
5. DO contact a qualified service technician for installation of this heater to ensure it is installed
in accordance with information contained herein and with national, state, and local codes and
regulations.
1

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the 2100 Series and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Steffes 2100 Series

  • Page 1 • Disclaimer: In compiling this manual, Steffes has used its best judgement based upon information available, but disclaims any responsibility or liability for any errors or miscalculations contained herein, or any revisions hereof, or which result, in whole or in part, from the use of this manual or any revisions hereof.
  • Page 2 IDENTIFY HEATER TYPE Steffes heaters are available for connection to different input voltages. Standard configuration for direct- wired heaters is 240V; cord-connected heaters are configured to plug into a 120V wall outlet. To determine the configuration of the heater, refer to the Unit Identification Label on the lower left side panel. All heaters are UL and cUL safety listed.
  • Page 3 INSTALLATION 1. Remove the heater from the box and lift it off the shipping WARNING pallet. Place the shipping box aside until the brick loading process (Section 9). Risk of fire. Can cause injury or death. Failure to secure the heater can cause 2.
  • Page 4 CONNECTING PLUG-IN HEATER WARNING • HAZARDOUS VOLTAGE: Risk of electric shock. Can cause injury or death. DO NOT energize the heater until installation is complete. Equipment must be installed by a qualified technician in accordance with applicable local, state, and national codes and regulations.
  • Page 5 PEAK CONTROL METHOD POWER LINE CARRIER (PLC) PEAK CONTROL The 2100 series room heater is factory-configured for use with power line carrier (PLC) control. The PLC transceiver (sold separately) sends peak control and outdoor temperature information to all the heaters in the building, eliminating the need for low voltage wiring to each heater.
  • Page 6 IMPORTANT provides this information to the heater. The heater responds by automatically storing heat in its brick core according to outdoor f connecting to the Steffes power line temperature and the heating requirements. carrier (PLC) system, refer to the PLC Installation Methods: Owner’s and Installer’s Guide.
  • Page 7 Row 1 SIDE VIEW CONFIGURATION MENU IMPORTANT The Steffes 2100 Series room heaters have a Configuration If access to Configuration Menu times Menu, which allows the heaters to be customized for the out, the heater must be powered off equipment installed and the power company consumers’...
  • Page 8 Verify all fuses and/or circuit breakers are labeled in the breaker panel. • Give the customer the User’s Guide and warranty registration card. The registration card must be submitted to ensure warranty coverage. 3050 Hwy 22 North | Dickinson, ND 58601-9413 USA| www.steffes.com Part No. 1206079 Rev. 0...

This manual is also suitable for:

210221032104210521062102pi

Table of Contents