C-UL: Bears the C-UL Mark and is in compliance with Canadian Safety Regulations according to 950. FCC Information 1. Use the attached specified cables with the LCD3000 (L30HV201) color monitor so as not to interfere with radio and television reception. (1) Please use the supplied power cord or equivalent to ensure FCC compliance.
Refer all servicing to qualified service personnel. • Do not spill any liquids into the cabinet or use your monitor near water. • Do not insert objects of any kind into the cabinet slots, as they may touch dangerous voltage points, which can be harmful or fatal or may cause electric shock, fire or equipment failure.
Wireless Remote Control and AA Batteries *Remember to save your original box and packing material to transport or ship the monitor. The following components are available to use with the LCD3000. To obtain the optional components and additional information, contact Customer Service at (800) 632-4662.
This device cannot be used or installed without the Tabletop Stand or other mounting accessory. For proper installation it is strongly recommended to use a trained, NEC authorized service person. Failure to follow NEC standard mounting procedures could result in damage to the equipment or injury to the user or installer. Prod- uct warranty does not cover damage caused by improper instal- lation.
Receives the signal from the remote control (when using the wireless remote control). See also page 8. Glows green when the LCD monitor is in active and glows red when the LCD is in POWER OFF mode. When the LCD is in power save mode, it will glow both green and red.
S-VIDEO IN connector (DIN 4 pin): To input the S-video (Y/C separate signal). EXTERNAL CONTROL (mini D-Sub 9 pin) RS232 IN connector: Use when operating the LCD monitor from the RGB equipment like a computer. EXTERNAL SPEAKER TERMINAL To output the audio signal from AUDIO 1, 2 or 3 jack.
REMOTE CONTROLLER RU-M104 POWER button Switches the power on/off. * If Power Indicator is not glowing, then no controls will work. INPUT button Selects from input signal, [RGB1], [RGB2], [RGB3], [DVD/ HD], [VIDEO]. AUDIO INPUT button Selects from input audio signal, [AUDIO1], [AUDIO2], [AUDIO3] SIZE button Selects picture size, [FULL], [NORMAL], [WIDE].
Use the remote control within a distance of about 7 m/23 ft. from the front of the LCD monitor's remote control sensor and at a hori- zontal and vertical angle of within 30° within a distance of about 3 m/10 ft.
3. Replace the cover. Remove the cover Insert the batteries CAUTION Incorrect usage of batteries can result in leaks or bursting. NEC recommends the following battery use: • Place "AA" size batteries matching the + and - signs on each battery to the + and - signs of the battery compartment.
Refer to the user manual included with each separate piece of equipment. LCD monitor DVD player Personal computer HD or laser disc player Wiring Diagram Personal computer Audio signal of input device Equipment with digital interface EXIT INPUT MUTE LCD monitor (second monitor)
D-sub 15 pin). • To connect the RGB 3 DVD/HD IN connector (BNC) on the LCD monitor, use a signal cable (mini D-sub 15 pin to BNC x 5). Select RGB 3 from the INPUT button. When connecting one or more LCD monitors, use the RGB OUT connector (BNC).
To maintain display quality, use a cable recommended by DVI standards. • The AUDIO IN 1, 2 and 3 can be used for audio input. For connection, select AUDIO 1, 2 or 3 from the AUDIO INPUT button. LCD monitor To audio output To DVI output...
Connecting to a VCR or Laser Disc Player Connecting your VCR or laser disc player to your LCD monitor will enable you to display your VCR or laser disc player video. Refer to your VCR or laser disc player owner's manual for more information.
• To connect the RGB 3 DVD/HD In connector (BNC) on the LCD monitor, use a separately available BNC connector cable. You will need a BNC-to-RCA adapter to connect a DVD player with an RCA pin jack to the BNC connector cable (not provided).
Turn on the LCD monitor and the amplifier only after all hookups have been made. • Use an RCA cable to connect the AUDIO OUT connector (RCA) on the LCD monitor and the audio input on the amplifier. • Do not reverse the audio left and right jacks.
The LCD monitor power indicator will turn green while powered on or red in off mode. The monitor can be powered on or off using the following three options: Power Switch er Switch –Power ON and OFF Modes 1. Pressing the power button.
Power Standby Red and Green When Using Power Management Function The LCD monitor follows the VESA approved DPMS Power Man- agement function. The power management function is an energy saving function that automatically reduces the power consumption of the display when the keyboard or the mouse has not been used for a fixed period of time.
Press UP or DOWN button to select sub-menu Remote Control Press UP or DOWN button to select Control Panel UP or DOWN button OSM screen BRIGHTNESS CONTRAST SHARPNESS BLACK LEVEL COLOR CONTROL COLOR TEMPERATURE PICTURE RESET :SEL EXIT:PRE SET:NEXT MENU:END Main-Menu PICTURE Sub-Menu...
–Computer continued BRIGHTNESS CONTRAST SHARPNESS COLOR TEMPERATURE BLACK LEVEL COLOR CONTROL COLOR TEMPERATURE PICTURE RESET :SEL EXIT:PRE SET:NEXT MENU:END BRIGHTNESS CONTRAST SHARPNESS PICTURE RESET BLACK LEVEL COLOR CONTROL COLOR TEMPERATURE PICTURE RESET :SEL EXIT:PRE SET:NEXT MENU:END Main-Menu SCREEN Sub-Menu H POSITION V POSITION CLOCK H POSITION...
Time from 3 to 30 seconds is available. :SEL EXIT:PRE MENU:END In the OFF TIMER menu, you can preset the OFF TIMER monitor to automatically power down. A time between 1 to 24 hours is available. :SEL EXIT:PRE MENU:END To select SCREEN SAVER mode, select ON/OFF...
–DVD & HD Main-Menu PICTURE Sub-Menu BRIGHTNESS CONTRAST SHARPNESS BRIGHTNESS COLOR BLACK LEVEL PICTURE RESET :SEL EXIT:PRE SET:NEXT MENU:END BRIGHTNESS CONTRAST SHARPNESS CONTRAST COLOR BLACK LEVEL PICTURE RESET :SEL EXIT:PRE SET:NEXT MENU:END BRIGHTNESS CONTRAST SHARPNESS SHARPNESS COLOR BLACK LEVEL PICTURE RESET :SEL EXIT:PRE SET:NEXT MENU:END BRIGHTNESS CONTRAST...
EXIT:PRE MENU:END To select OFF TIMER mode ON/OFF. OFF TIMER In the OFF TIMER menu, you can preset the monitor to automatically power down. A time between 1 to 24 hours is available. :SEL EXIT:PRE MENU:END To select SCREEN SAVER mode, select ON/OFF...
MENU:END To select OFF TIMER mode ON/OFF. OFF TIMER In the OFF TIMER menu, you can select how long monitor auto turn off time after monitor turn on. A time between 1 to 24 hours is available. :SEL EEXIT:PRE MENU:END...
–AV Input continued LANGUAGE OSM TIME OFF TIMER COLOR SYSTEM SCREEN SAVER COLOR SYSTEM CONFIGURATION RESET :SEL EXIT:PRE SET:NEXT MENU:END LANGUAGE OSM TIME OFF TIMER CONFIGURATION RESET SCREEN SAVER COLOR SYSTEM CONFIGURATION RESET :SEL EXIT:PRE SET:NEXT MENU:END Selecting the Color System depends on your input COLOR SYSTEM video format.
This LCD monitor can be controlled by connecting a personal computer with a RS-232C terminal. Functions that can be controlled by a personal computer are: • Power ON or OFF • Switching between input signals Connection LCD Monitor + PC Note: If your PC (IBM or IBM compatible) is equipped only with a 25-pin serial port connector, a 25-pin serial port adapter is required.
(1) The command from a personal computer to the LCD monitor will be sent in 400ms. (2) The LCD monitor will send a return command 400ms* after it has received an encode. If the command isn't received correctly, the LCD monitor will not send the return command.
® ) puts you in complete control of display setting adjustments. NEC’s quality and reliability provide peace of mind with a 1-year onsite warranty (including backlight) and 24/7 customer service and technical support. No Touch Auto Adjust: No Touch Auto Adjust automatically adjusts the monitor to optimal settings upon initial setup.
LCD monitors’ image persistence is not permanent. To alleviate image persistence, turn the monitor off for as long as an image was displayed. If an image was on the monitor for one hour and a ”ghost” of that image remains, the monitor should be turned off for one hour to erase the image.
NEC-Mitsubishi Monitor Customer Service & Support Customer Service and Technical Support: Parts and Accessories/Macintosh Cable Adapter: Customer Service Policies & Processes: Online Technical Support Knowledge Base: Customer Service & Technical Support Email: Sales and Product Information Sales Information Line Canadian Customers...
640 x 480 at 60 Hz 800 x 600 at 60 Hz 1024 x 768 at 60 Hz NEC-Mitsubishi Electronics Display cites recommended resolution 1280 x 768 at 60 Hz ... at 60 Hz for optimal display performance. NTSC / PAL...
NEC-Mitsubishi Electronics Display of America, Inc. (hereinafter “NMD-A”) warrants this Product to be free from defects in material and workmanship and, subject to the conditions set forth below, agrees to repair or replace (at NMD-A’s sole option) any part of the enclosed unit which proves defective for a period of one (1) year from the date of first consumer purchase.
LCD3000 is in compliance with Council Directive 73/23/EEC: – EN 60950 Council Directive 89/336/EEC: — EN 55022 — EN 61000-3-2 — EN 61000-3-3 — EN 55024 and marked with NEC-Mitsubishi Electric Visual Systems Corporation 4-13-23, Shibaura, Minato-Ku Tokyo 108-0023, Japan...
FCC Rules. Windows is a registered trademark of Microsoft Corporation. NEC is a registered trademark of NEC Corporation. All other brands and product names are trademarks or registered trademarks of their respective owners.