Cisco TelePresence MX Series Administrator's Manual page 92

Cisco TelePresence MX Series
Contents
Video SelfviewDefault OnMonitorRole
Determine which monitor/output to display the main video source (self view) on after a call.
The value reflects the monitor role set for the output in the Video Output Internal MonitorRole
setting.
The setting applies both when self view is displayed in full screen, and when it is displayed as
picture-in-picture (PiP), but only if the Video Monitors setting is set to Dual.
Requires user role: ADMIN
Value space: <First/Second/Current>
First: The self view picture will be shown on outputs with the Video Output LCD/Internal
MonitorRole set to First.
Second: The self view picture will be shown on outputs with the Video Output LCD/Internal
MonitorRole set to Second.
Current: When leaving the call, the self view picture will be kept on the same output as
during the call.
Video SelfviewDefault OnMonitorRole: Current
Example:
Video CamCtrlPip CallSetup Mode
This setting is used to switch on self view for a short while when setting up a call. The Video
CamCtrlPip CallSetup Duration setting determines for how long it remains on. This applies when
self view in general is switched off.
Requires user role: ADMIN
Value space: <Off/On>
Off: Self view is not shown automatically during call setup.
On: Self view is shown automatically during call setup.
Video CamCtrlPip CallSetup Mode: Off
Example:
Video CamCtrlPip CallSetup Duration
This setting only has an effect when the Video CamCtrlPip CallSetup Mode setting is switched
On. In this case, the number of seconds set here determines for how long self view is shown
before it is automatically switched off.
Requires user role: ADMIN
Value space: <1..60>
Range: Choose for how long self view remains on. The valid range is between 1 and 60
seconds.
Video CamCtrlPip CallSetup Duration: 10
Example:
D14850.05 MX Series Administrator Guide TC6.1, APRIL 2013.
Introduction Web interface System settings System settings
Video PIP ActiveSpeaker DefaultValue Position
Determine the position on screen of the active speaker picture-in-picture (PiP). The setting only
takes effect when using a video layout where the active speaker is a PiP, i.e. the Overlay layout,
or possibly a Custom layout (see the Video Layout LocalLayoutFamily setting). The setting takes
effect from the next call onwards; if changed during a call, it will have no effect on the current
call.
Requires user role: ADMIN
Value space: <Current/UpperLeft/UpperCenter/UpperRight/CenterLeft/CenterRight/LowerLeft/
LowerRight>
Current: The position of the active speaker PiP will be kept unchanged when leaving a call.
UpperLeft: The active speaker PiP will appear in the upper left corner of the screen.
UpperCenter: The active speaker PiP will appear in the upper center position.
UpperRight: The active speaker PiP will appear in the upper right corner of the screen.
CenterLeft: The active speaker PiP will appear in the center left position.
CentreRight: The active speaker PiP will appear in the center right position.
LowerLeft: The active speaker PiP will appear in the lower left corner of the screen.
LowerRight: The active speaker PiP will appear in the lower right corner of the screen.
Video PIP ActiveSpeaker DefaultValue Position: Current
Example:
Video PIP Presentation DefaultValue Position
Determine the position on screen of the presentation picture-in-picture (PiP). The setting only
takes effect when the presentation is explicitly minimized to a PiP, for example using the Touch
controller. The setting takes effect from the next call onwards; if changed during a call, it will
have no effect on the current call.
Requires user role: ADMIN
Value space: <Current/UpperLeft/UpperCenter/UpperRight/CenterLeft/CenterRight/LowerLeft/
LowerRight >
Current: The position of the presentation PiP will be kept unchanged when leaving a call.
UpperLeft: The presentation PiP will appear in the upper left corner of the screen.
UpperCenter: The presentation PiP will appear in the upper center position.
UpperRight: The presentation PiP will appear in the upper right corner of the screen.
CenterLeft: The presentation PiP will appear in the center left position.
CentreRight: The presentation PiP will appear in the center right position.
LowerLeft: The presentation PiP will appear in the lower left corner of the screen.
LowerRight: The presentation PiP will appear in the lower right corner of the screen.
Video PIP Presentation DefaultValue Position: Current
Example:
www.cisco.com — Copyright © 2011–2013 Cisco Systems, Inc. All rights reserved.
92
Administrator Guide
Setting passwords Appendices