Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for DENAGO eXC 2
Summary of Contents for DENAGO eXC 2
- Page 1 QUICKSTART GUIDE eXC 2...
- Page 2 With over 100 years of collective experience, our team loves to share with you what we learned from riding, working in bike shops and working in the bike industry. We are looking forward to you joining us for a ride.
- Page 3 THANK YOU and welcome to the Denago team. We value and appreciate you and your choice. If there is anything you need, please reach out and let us know how we can help. Email: cs@denago.com Call Us: 877-755-2453 (BIKE)
-
Page 4: Always Wear A Helmet
ALWAYS WEAR A HELMET Please make sure you read, understand and follow the instructions in the quickstart guide as eBikes are new to most riders. For more information, please visit: denago.zendesk.com... - Page 5 EXC MODEL 2 EXC MODEL 2 5 | DENAGO...
-
Page 6: What's In The Box
WHAT’S IN THE BOX The following accessories are included with your 90% pre-assembled Denago bike. Multi Tool Pedal / Wheel Wrench Bicycle grease packet Pedals Battery Charger Battery Keys 6 | DENAGO QUICKSTART GUIDE... - Page 7 The quickstart guide will assist you in completing the assembly. By following the directions, you will be able to get outside and start riding your new Denago eBike in less than 30 minutes. If you are not comfortable or confi dent, please take your...
-
Page 8: Getting Started
GETTING STARTED... - Page 9 Unpack and Unwrap your eBike EXC MODEL 2 9 | DENAGO...
- Page 10 We’d like to make your assembly process a bit easier. So we made a Parts & Tools layout inside the box. Please lay Parts & Tools into each area. Front Wheel Tool Set & Parts Pedals Other Stuff 10 | DENAGO QUICKSTART GUIDE...
-
Page 11: Assembly Steps
ASSEMBLY STEPS 1. HANDLEBAR 2. SADDLE 3. FRONT WHEEL & BRAKE 4. PEDALS 5. DISPLAY 6. ADJUSTMENTS... - Page 12 4. Install the display on the right side 5. Finally, lock the display with the 6. Tighten the front reflector with a of the stem with a 2.5mm hex tool after 2.5mm hex tool. Phillips screw-driver removing the fixing screws 12 | DENAGO QUICKSTART GUIDE...
- Page 13 Philips screwdriver. THE USAGE OF DROPPER POST 1. Without weight on the saddle, 2. To lower the seatpost, press the press the remote to raise the seat post. remote while applying bodyweight on the saddle. EXC MODEL 2 13 | DENAGO...
- Page 14 REINSTALL THE PACKING BLOCK EACH TIME YOU REMOVE THE FRONT WHEEL. CAUTION Tighten Thru-axle securely to the fork dropouts. 4. Finally, insert the shaft into place on the right side of the front fork and lock it with 6mm hex tool. 14 | DENAGO QUICKSTART GUIDE...
- Page 15 Improper installation of the front wheel and or handlebar stem can cause loss of control, accidents, serious injury or death. Check regularly that the front wheel and handlebar stem are ALWAYS properly secure and in good working condition. 15 | DENAGO...
- Page 16 1. For the NON Drive Side of Bike, select L-Left pedal. 2. Apply grease to pedal threads. 3. Insert Pedal into Crank Arm/NON- Drive side and start to turn COUNTER CLOCKWISE. 4. Once hand tight apply 15mm wrench to pedal and tighten and secure. 16 | DENAGO QUICKSTART GUIDE...
- Page 17 EXC MODEL 2 17 | DENAGO...
- Page 18 The lowest mode is E, the highest mode is B (which can be set). On the default is mode E, number “0”means no power assistance. 18 | DENAGO QUICKSTART GUIDE...
- Page 19 Sport the sport mode Sport+ the sport plus mode Boost the strongest sport mode PAS (Pedal Assist System) comes with the ability to set your MAX speed while also adjusting your PAS level speeds. EXC MODEL 2 19 | DENAGO...
-
Page 20: Assembly | Adjustments
ASSEMBLY | ADJUSTMENTS Please confi rm HANDLEBARS AND FRONT WHEEL are in alignment. 20 | DENAGO QUICKSTART GUIDE... - Page 21 Owner’s Manual and more comprehensive details are available online. Please go to DENAGO.ZENDESK.COM for content and video support You’re almost finished, but now is the time for the final adjustments and safety check. Then you will be ready for a test ride.
- Page 22 Check the PAS setting - Ideally you want to start in PAS0 or PAS1. See Speed Adjustment to help find your most comfortable setting. YOU ARE READY to RIDE. ENJOY! 22 | DENAGO QUICKSTART GUIDE...
- Page 23 SOME OTHER IMPORTANT THINGS...
-
Page 24: Battery | Details
Keep battery and charger away from children. DO NOT ever cover the battery or charger. This could cause overheating and potential fire. DO NOT open the battery housing. You will void all warranties and potential for serious injury and or death could occur. 24 | DENAGO... - Page 25 Key is not needed to install battery. 4. Key is not needed to install battery but if in place remove 2. Place bottom of battery into frame and enjoy the ride. and push battery into the top. EXC MODEL 2 25 | DENAGO...
- Page 26 INTENDED USE AND SAFETY CHECK Warranty Information Owner’s Manual How-to Videos and more info Available at denago.zendesk.com If you need any help, please give us a call 877-755-2453 (bike) or email cs@denago.com...
- Page 27 For your safety, please do the following inspection before and after each ride. If you discover any concerns with your bike, please seek professional service or contact us at CS@DENAGO.COM or 877-755-2453 (BIKE) to help resolve any issues. Make sure your battery is at FULL Charge.
Need help?
Do you have a question about the eXC 2 and is the answer not in the manual?
Questions and answers