Table of Contents
Advertisement
Operation Guide 5444/5524
3. When the timekeeping setting you want to change is flashing, use D and/or B
to change it as described below.
Screen
To do this:
Change the city code
Cycle between Auto DST (AUTO), Daylight
Saving Time (ON) and Standard Time (OFF)
Toggle between 12-hour (12H) and 24-hour
(24H) timekeeping
Reset the seconds to 00
Change the hour or minute
Change the year, month, or day
Toggle between button operation tone on
(KEY ) and off (MUTE)
Toggle the illumination duration between
three seconds (LT3) and 1.5 seconds (LT1)
E-50
The watch's built-in full automatic calendar makes allowances for different month
lengths and leap years. Once you set the date, there should be no reason to
change it except after you have the watch's rechargeable battery replaced or after
power drops to Level 5 (page E-15).
The day of the week changes automatically when the date changes.
Refer to the pages shown below for more information on Timekeeping Mode
settings.
−
Button operation tone on/off: "To turn the button operation tone on and off"
(page E-81)
−
Enabling and disabling power saving: "To turn Power Saving on and off" (page E-83)
−
The illumination duration: "To change the illumination duration" (page E-69)
E-52
To specify standard time or daylight saving time (DST) for a city
1. In the World Time Mode, use D (East) to scroll
DST indicator
through the city codes in the right digital dial until
the one whose Standard Time/Daylight Saving Time
setting you want to change is displayed.
2. Hold down A for about two seconds until the watch
beeps.
This toggles the city code you selected in step 1
between Daylight Saving Time (DST indicator
displayed in the left digital dial) and standard time
(DST indicator not displayed).
Using the World Time Mode to change the DST setting of the city code that is
selected as your Home City also will change the Timekeeping Mode time DST
setting.
Note that you cannot switch between standard time/daylight saving time (DST)
while UTC is selected as the World Time City.
E-54
Note
If you are using the watch in Japan, be sure to select TYO (Tokyo) as your Home
City. Selecting another city code will make it impossible to receive the time
calibration signal, which will cause the watch's time setting to be off.
E-56
To perform an elapsed time operation
D
D
D
Start
Stop
Resume
To pause at a split time
D
A
A
Start
Split
Split release
(SPL displayed)
To measure two finishes
D
A
D
Start
Split
Stop
(SPL displayed)
Second runner
First runner finishes.
finishes.
Display time of first
runner.
E-58
4. Press A to exit the setting mode.
Do this:
Use D (East) and B (West).
Press D.
Note
For information about selecting a Home City and configuring the DST setting, see
"Configuring Home City Settings" (page E-42).
Use D (+) and B (–).
While 12-hour format is selected for timekeeping, a PM indicator will appear for
times from noon to 11:59 p.m. No indicator appears for times from midnight to
11:59 a.m. With 24-hour format, time is displayed from 0:00 to 23:59, without any
PM indicator.
Press D.
Using the World Time Mode
Current time in the
currently selected World
Time City
To swap your Home Time and World Time Cities
1. In the World Time Mode, use D to select the city you want to use as your new
Home City.
2. To swap, hold down A and B at the same time until the watch beeps.
Using the Stopwatch
The stopwatch measures elapsed time, split times, and two finishes.
Minutes Seconds
Note
The Stopwatch Mode can indicate elapsed time up to 59 minutes, 59.99 seconds.
D
A
An ongoing elapsed time measurement operation will continue internally even if
(Stop)
Reset
you change to another mode. However, if you exit the Stopwatch Mode while a
split time is displayed, the split time will not be displayed when you return to the
Stopwatch Mode.
D
A
Stop
Reset
A
A
Split release
Reset
Display time of
second runner.
The watch automatically adjusts its analog setting to match the current time
displayed in the left digital dial.
Exiting a setting mode will normally cause the hands to return to regular
timekeeping automatically. However, if you manually move the hands (page
E-79) and then enter a setting mode, they will not return to regular timekeeping
automatically when you exit the setting mode. In this case, you will need to
return the hands to their normal positions manually (page E-80).
You can use the World Time Mode to view the current
Currently selected
time in one of 31 time zones (48 cities) around the globe.
World Time City
The city that is currently selected in the World Time Mode
is called the "World Time City".
To enter the World Time Mode
Use C to select the World Time Mode as shown on
page E-38.
The right digital dial will show WT for about one second.
After that, the city code and city name will scroll once
across the right digital dial, and then the three-letter
corresponding city code will be displayed.
To view the time in another time zone
In the World Time Mode, use D (East) to scroll through
city codes.
The standard time/daylight saving time (DST) setting affects only the currently
selected time zone. Other time zones are not affected.
A and B
This will make the World Time City you selected in step 1 (NYC (New York)) your
new Home City.
Your previous Home City (TYO (Tokyo)) will be your new World Time City.
To enter the Stopwatch Mode
Use C to select the Stopwatch Mode (STW) as shown
on page E-39.
1/100 second
E-51
E-53
E-55
E-57
E-59
Advertisement
Table of Contents
