Casio 5517 Operation Manual

MA1710-EA © 2017 CASIO COMPUTER CO., LTD.
Operation Guide ANA(H3H-1)
Be sure to keep all user documentation handy for future reference.
Your watch may differ somewhat from the one shown in the illustration.
Some models may use a combination of hands and rotating disks to indicate
information. The word "hand" in this section is used to mean both analog hands
and rotating disks.
Stopwatch Minute Hand
Second Hand
Stopwatch Second Hand
Stopwatch functions

To adjust the time setting

When the second hand is at
12 o'clock, pull the Crown
Click 2.
Rotate the to change the
Crown
time setting.
Push the back in on a time
Crown
signal to resume timekeeping.
Note
Take care that you set the correct AM
or PM time.
When changing the time, move the
minute hand four or five minutes past
your final setting, and then back it up
to the setting you want.

Crown Operations

Some water-resistant models (100 meters, 200 meters)
have a screw-in crown. When you need to perform a crown
operation, rotate it towards you to unscrew it. Then pull
the crown out. Avoid applying undue force when pulling.
The watch loses its water resistance while the crown is
unscrewed. After performing a crown operation, fully screw
the crown back in.
If your watch has a rotary bezel...
You can rotate the bezel to align its ▼ mark with the
minute hand. Then you will be able to tell how much
time has elapsed since aligning the ▼ mark.
Stopwatch 1/10-Second Hand
Hour Hand Minute Hand
A
Click 2
Click 1
B
Crown
Day Indicator

To change the day indicator setting

Pull the out to Click 1.
Crown
out to
Rotate the away from you
Crown
to set the day.
Push the back in.
Crown
Note
The day indicator setting uses a 31-
day month. Make adjustments for
months of shorter lengths.
Avoid changing the day indicator
setting between the hours of 9
p.m. and 1 a.m. Otherwise, the day
indicator may not change correctly at
midnight.
Start
Elapsed time
Current

Using the Stopwatch

The stopwatch measures elapsed time in 1/10-second increments up to 59 minutes,
59.9 seconds.
Elapsed time
A
Start
Split time
A
Start
Two finishes
A
Start
Important!
Do not operate the stopwatch with the crown pulled out.
Note
An elapsed time operation will stop automatically at the end of 60 minutes.

Correcting the 0 Positions of the Hands

Perform the following procedure if the stopwatch hands do not return to their 0 (zero)
positions when you reset the stopwatch.
Pull the Crown
Press A to move the
Holding down A will move the hand at high speed.
Press B to move the
Holding down B will move the hand at high speed.
The
Stopwatch Minute Hand
After all of the hands are the way you want, push the
Important!
Timekeeping stops while the crown is pulled out. Correct the current time setting
after performing the above operation.

Specifications

Crown
Module No.
5517/5521
5579
Loosen
Stopwatch: Measuring Capacity: 59'59.9" (60 minutes)
Measuring Unit: 1/10 second
Measurements: Elapsed time; split time; two finishes
Specifications are subject to change without notice.
A A
A
Stop Resume Stop
B A
B
Split Split release Stop
A B
B
Split Stop Split release
Display time of
First runner Second runner
second runner.
finishes. finishes.
Display time of first
runner.
out to Click 2.
clockwise.
Stopwatch 1/10-Second Hand
clockwise.
Stopwatch Second Hand
is synchronized with the
Stopwatch Second Hand
Accuracy at normal
Battery type
temperature (per month)
±20 seconds SR920SW
±20 seconds SR920SW
B
Reset
B
Reset
B
Reset
.
Crown back in.
Battery life
(60 minutes stopwatch
operation per day)
Approx. 2 years
Approx. 3 years
1