Supermicro AS -1124US-TNRP Quick Reference Manual

A+ Server AS -1124US-TNRP Quick Reference Guide
Board Layout
1 2
3
4 5
7 8 9
10
H12DSU-iN
11 REV:
DESIGNED IN USA
12
13 14 15 16 17
No. Description
1 SXB1A/1B/1C: WIO-L Riser Card Support (CPU2 PCI-E 4.0 x32)
2
SXB2: WIO-R Riser Card Support (CPU2 PCI-E 4.0 x16)
3 SXB3A/3B/3C: Ultra I/O Riser Card Support (CPU1 PCI-E 4.0 x40)
4 P1 NVMe 0/1 SATA0-7
5 SATA 3.0 8-9
6 USB 3.0 2
7 P2 NVMe0 SATA10-13
8 P2 NMVe1 SATA14-17
9 P1 NVMe2-3
10 P2 NVMe2-3
11 USB 3.0 3-4
12 JBT1
13 P2 DIMMA1-D2 slots
14 CPU2
15 P2 DIMME1-H2 slots
16 P1 DIMMA1-D2 slots
17 CPU1
18 P1 DIMME1-H2 slots
Removing a Hot-Swap
Drive Carrier from
the Chassis
1. Press the release button on the
drive carrier, which will extend
2
the drive carrier handle.
2. Use the drive carrier handle to
pull the drive out of the chassis.
Release
Button 1
Memory
CPU2
6
DIMM Module Population Sequence
When installing memory modules, the DIMM slots should be populated in the following
order: DIMMA2, DIMMB2, DIMMC2, DIMMD2, DIMME2, DIMMF2, DIMMG2, DIMMH2, then
DIMMA1, DIMMB1, DIMMC1, DIMMD1, DIMME1, DIMMF1, DIMMG1, DIMMH1.
•
•
Always use DDR4 DIMM modules of the same type, size and speed.
•
Mixed DIMM speeds can be installed. However, all DIMMs will run at the speed of the
slowest DIMM.
18
•
The motherboard supports an odd number of modules (1, 3, etc.). However, to achieve the
best memory performance, a balanced memory population is recommended.
Processors and Their Corresponding Memory Modules
CPU# Channel Channel Channel Channel
1 2 3 4
8 DIMMS
CPU1 C2 D2
CPU2 C2 D2
16 DIMMS
CPU1 A2 B2 C2 D2
CPU2 A2 B2 C2 D2
32 DIMMS
CPU1 A1 A2 B1 B2 C1 C2 D1 D2
CPU2 A1 A2 B1 B2 C1 C2 D1 D2
Hard Drive Installation
Installing a Drive
1. Insert a drive into the carrier with the PCB side facing down and the connector end
toward the rear of the carrier. Place the drive in the carrier so that the screw holes line
up.
2. The drive carrier has a tool-less design but you also have the option to secure the
drive to the carrier with two M3 screws. These screws are included in the chassis
accessory box.
3. Insert the drive carrier with the disk drive into its bay, keeping the carrier oriented
so that the hard drive is on the top of the carrier and the release button is on the right
side. When the carrier reaches the rear of the bay, the release handle will retract.
4. Push the handle in until it clicks into its locked position.
Front View & Interface
CPU1
CPU1
HDD1 HDD3
HDD0 HDD2
UID
1 2
No. Description
1 UID Button
2 Universal Information LED
3 NIC1 LED
4 Device Activity LED
Processor Installation
1. Removing the Processor Force Frame
Use a Torx T20 driver to loosen the screws holding
down Force Frame in the sequence of 3-2-1. The
screws are numbered on the Force Frame next to each
screw hole.
Screw #3
Screw #2
Channel Channel Channel Channel
5 6 7 8
G2 H2 Force Frame
G2 H2
5. Inserting the Carrier Frame/CPU Package
E2 F2 G2 H2 Carrier Frame/
CPU Package
E2 F2 G2 H2
E1 E2 F1 F2 G1 G2 H1 H2
E1 E2 F1 F2 G1 G2 H1 H2
1. Mounting the Heatsink
CPU2
HDD5 HDD7 HDD9 HDD11
HDD4 HDD6 HDD8 HDD10
NVME / SATA3.0
9
*
Optional SAS support
No.
1
3 4 5 6
No. Description
5 Power LED
6 Power Button
*Redundancy based on configuration and application load
CPU Installation
2. Raising the Force Frame 3. Lifting the Rail Frame
Screw #1
6. Lowering the Force Frame 7. Securing the Force Frame
Secure the screws in the order
16.1 kgf-cm (14 lbf-in) of torque.
secures both the Rail Frame and CPU Package.
Caution: Tightening must be executed in proper
1-2-3 sequence to avoid causing catastrophic
damage to the socket or CPU Package.
Heatsink Installation

2. Securing the Heatsink
!
SAFETY INFORMATION
Using a diagonal pattern and a Torx T20 driver, tighten the four
IMPORTANT: See installation instructions and safety warning before
heatsink screws evenly to 16.1 kgf-cm (14.0 lbf-in) torque.
connecting system to power supply.
http://www.supermicro.com/about/policies/safety_information.cfm

#1 Screw
!
WARNING:
To reduce risk of electric shock/damage to equipment, disconnect power
#3 Screw
from server by disconnecting all power cords from electrical outlets.
#4 Screw
If any CPU socket empty, install protective plastic CPU cap.

!
WARNING:
Always be sure all power supplies for this system have the same power
output. If mixed power supplies are installed, the system will not operate.
#2 Screw
For more information go to : http://www.supermicro.com/support
http://www.supermicro.com MNL-2286-QRG
Rear View
8 7 6 5 4 3 2
1
Description
1 Two PCI-E x16 (FH 9.5") Slots
2 PCI-E x16 (LP) Slot
3 VGA Port
4 UID LED
5 Serial Port
6 Dedicated LAN for IPMI
7 Two USB 3.0 Ports
Two 10G RJ45 Ports and Two 10G SFP+ Ports
8
9 *Redundant Power Supply Modules
4. Removing the External Cap and PnP
Cover Cap
Rail Frame
PnP Cover Cap
External Cap
PnP Cover Cap
8. The Force Frame Secured
1-2-3, tightening to
The Force Frame
Caution
Rev. 1.0a