Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for HIKVISION 6825
Summary of Contents for HIKVISION 6825
-
Page 1: Installation And Configuration Guide For Dual-Lens People Counting Camera
Installation and Configuration Guide for Dual- lens 6825 People Counting Camera... -
Page 2: Table Of Contents
Content Installation and Configuration Guide for Dual-lens People Counting Camera ..........1 Chapter 1. Brief introduction ......................... 3 Chapter 2. Installation specification ......................4 2.1 Focal length and counting width ..................4 2.2 Accessaries ......................... 7 2.3 Installation steps ........................ 7 2.4 Counting configuration .................... -
Page 3: Chapter 1. Brief Introduction
Chapter 1. Brief introduction DS-2CD6825G0/C-I(V)(S), dual-lens camera, based on the binocular stereo vision technology, adopting 3D head detection and 3D tracking, can obtain accurate real-time trajectory of all moving objects within the monitoring scope, analyze the trajectory data and achieve high-precision people counting. It is very suitable for places where people counting is needed, such as shopping mall, supermarket, chain store, the scenic spot, subway station, bus station, exhibition hall, etc. -
Page 4: Chapter 2. Installation Specification
Chapter 2. Installation specification 2.1 Focal length and counting width The counting width depends on the installation height. The recommended installation height for dual-lens camera is less than 6.0m (19.7ft). The specific corresponding relation shown below: Focal length Installation height Max. - Page 5 Focal length Installation height Max. counting width Max. counting depth (mm/ft) （m/ft） （m/ft） （m/ft） 3.7/12.1 5.12/16.8 2.88/9.4 3.8/12.5 5.38/17.7 3.02/9.9 3.9/12.8 5.63/18.5 3.17/10.4 4.0/13 5.89/19.3 3.31/10.9 4.1/13.5 6.14/20.1 3.46/11.4 4.2/13.8 6.4/21 3.6/11.8 4.3/14.1 6.66/21.9 3.74/12.3 4.4/14.4 6.91/22.7 3.89/12.8 4.5/14.8 7.17/23.5 4.03/13.2 4.6/15.1 5.5/18...
- Page 6 Focal length Installation height Max. counting width Max. counting depth (mm/ft) （m/ft） （m/ft） （m/ft） 5.8/19 7.78/25.5 4.36/14.3 5.9/19.4 7.97/26.1 4.47/14.7 6/19.7 8.16/26.8 4.57/15...
-
Page 7: Accessaries
2.2 Accessaries Dual-lens Camera Drill Template Screws Quick guide 2.3 Installation steps Please pay great attention to the mounting position. Inappropriate mounting position may cause loss of accuracy. The recommended mounting position is shown below:... - Page 8 Horizontal sketch map of mounting position Vertical sketch map of mounting position Effect picture after installation Keep “HIKVISION” logo in the same direction as the “Front” arrow, see picture below:...
- Page 9 “Front” arrow and “HIKVISION” logo Make sure camera mounted vertically above the passenger flow(90°vertical by the ground), see picture below: Passenger flow（perpendicular to the door） For some scenarios where there are multiple cameras, mount the cameras according to two rules.
- Page 10 according to the overlap (see the yellow area below) of the adjacent two cameras’ counting width. The suggested overlapping length is between 0.2-0.5m. Sketch map of multiple cameras installation Notice 1) People flow should be in vertical up-and-down direction Passenger flow in horizontal direction (wrong) Passenger flow in slant direction (wrong)
- Page 11 Passenger flow in vertical up-and-down direction (right) 2) Passageway width should be within camera’s counting width 3) Avoid obstacles such glass door, shield door and turnstile that block the camera. For Each divided passageway, mount one camera right above 4) The camera should be mounted as close as possible to the passageway without obstacle. Remove the obstacle or adjust the camera mounting position if there is obstacle below the camera.
-
Page 12: Counting Configuration
Too far away from the door/Obstacle below camera Recommended installation 2.4 Counting configuration Configuration for single camera Step 1. Select VCA Resource. It is necessary to select the VCA source as People Counting Mode. Step 2. Rule Configuration: 1) Enter 【VCA】-【People Counting】, check “Enable People Counting”。 2) Select the calibration mode: Manual and Auto are selectable. - Page 13 Auto Calibration Mode: It will generate the lens height and a green calibration area automatically. The calibration area is used for calibrating the height from the ground to lens. So we strongly recommend to select the totally ground part as calibration area. Notice: If auto calibration fails, switch to [Manual] and input the measured “Height”, then click [Calibration].
- Page 14 Step 4. Draw detection line (the yellow line as shown in the below picture) or detection region. Detection Line: the yellow line should be within the blue detection region. Detection Region: Draw A and B region. Make sure the two areas don’t overlap. If the target enters from A region to B region, then it is counted as the entering number;...
-
Page 15: Configuration For Multiple Cameras
Step 5. Save it after finishing the configuration. Set the Arming schedule and linkage method. Configuration for multiple cameras Step 1. Do configuration for each camera following the steps above Step 2. Move each camera’s detection line and connect the ends of adjacent lines. Some objects could be placed on the image border for reference. -
Page 16: Parameter Description
Configuration of each detection line Parameter description Reverse Counting Alarm: Set reverse counting alarm (optional). Check Enable Reverse Entering Alarm to enable the function. An alarm is enabled when the target leaves the region. Set the arming schedule and linkage method. Shield Region: If you don’t want to count people of the specific area, you can draw the area as shield region. - Page 17 Data Uploading: 1) Enter 【VCA】-【People Counting】-【Data Uploading】 2) If you want to upload the real-time data to the platform, select real-time Upload Data as “ON’’. 3) If you want to adjust the statistic cycle manually, set data statistics data as required. 1/5/10/15/20/30/60 minutes are optional.
- Page 18 3) Daily Reset Time/Rest OSD: To reset the counter, you can set up a daily reset time. Or you can reset the OSD counter manually by click Manual Reset. 4) Display VCA Info. on Stream: It will display the ID number and height information of tracking people on stream after enabling it.
- Page 19 Advanced Parameter: 1) Height Filter: Enable the function and set a height value. Persons and objects shorter than the set value are not counted as a valid target. Also this camera support counting Children. 2) Target Detection Type/Algorithm Validity: There are four type of target detection: Detect based on the tracking algorithm only; Depth map only; Tracking algorithm mainly and depth map secondarily;...
-
Page 20: Chapter 3. Application Scenario
5) Clear Storage Data: To clear stored data on camera, you can click the Clear button. Always do the operation with caution. Deleted data cannot be restored. 6) One-touch Export: Export the device hardware settings, installation settings, people counting settings, rule settings and advanced settings. 7) Maintenance Mode: If the function is enabled, certain camera settings will be changed, such as the resolution, frame rate and bit rate. - Page 21 Mounting position and configuration for subway...