Advertisement
Quick Links
INSTALLATION INSTRUCTIONS
I
CEMAKER AND
Instructions for Non-30 Inch Wide Icemaker – Flavor Fusion Units . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Instructions for 30 Inch Wide Icemakers – Flavor Fusion Units . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Instructions for Non-30 Inch Wide Icemaker – IDC Series Units. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Instructions for 30 Inch Wide Icemaker – IDC Series Units. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Parts Included in the Kit are Shown in Table 1:
Part No.
22127
Icemaker Rear Mounting Plate
50904
Silicone sealant
620053922
Left Side Adapter Hold-Down Bracket
620053923
Right Side Adapter Hold-Down Bracket
620518916
Adaptor/Icemaker Side Hold-Down Plate (Flat)
620701601
#10-16 S.S. Sheetmetal Screws
Tools Needed:
•
Power Drill
•
9/64 in. (.140 in.) Drill Bit
•
#2 Phillips Head Screwdriver
I
NSTRUCTIONS FOR
WARNING: Failure to follow the installation instructions correctly may result in equipment damage
and/or personal injury.
The Parts shown in Table 2 are NOT Used for this Installation:
Part No.
620518916
Adaptor/Icemaker Side Hold-Down Plate (Flat)
1.
Remove the two top black side panel screws from both sides of the Flavor Fusion unit (See Figure 1) and
save the screws.
Release Date: June 30, 2008
© 2008, IMI Cornelius Inc.
A
H
DAPTER
OLD
F
F
F
OR
LAVOR
USION
Table 1
Description
N
-30 I
W
ON
NCH
Table 2
Description
www.cornelius.com
- 1 -
Icemaker & Adaptor Hold-Down Kit Installation Instructions
-D
K
P/N 629096853
OWN
IT
/ IDC
O
UNITS
I
– F
IDE
CEMAKER
NLY
Qty.
2
1 tube
1
1
2
12
F
U
LAVOR
USION
NITS
Qty.
2
Revision: 1
Publication Number: 629096853INS
Advertisement
Related Manuals for Cornelius Flavor Fusion 620053922
Summary of Contents for Cornelius Flavor Fusion 620053922
-
Page 1: Installation Instructions
Remove the two top black side panel screws from both sides of the Flavor Fusion unit (See Figure 1) and save the screws. Release Date: June 30, 2008 © 2008, IMI Cornelius Inc. Icemaker & Adaptor Hold-Down Kit Installation Instructions DAPTER... - Page 2 Place the bracket over the adapter lid then re-install the black screws that were removed in Step 1. Publication Number: 629096853INS Side Panel Screws Figure 1 Left Side Right Side Figure 2 Figure 3 - 2 - Straight Edge Goes to the Rear of the Dispenser © 2008, IMI Cornelius Inc.
- Page 3 NOTE: Kit contains two plates, both mounting plates must be installed. Using the plate as a template, drill 9/64 in. (0.140 in.) holes into the icemaker base and the dispenser, as shown in Figure 7. © 2008, IMI Cornelius Inc. Icemaker & Adaptor Hold-Down Kit Installation Instructions Flange on bracket...
- Page 4 Remove the two top black side panel screws from both sides of the Flavor Fusion unit (See Figure 1) and save the screws. Publication Number: 629096853INS Figure 7 – F CEMAKERS LAVOR Table 3 Description Figure 8 - 4 - USION NITS Qty. © 2008, IMI Cornelius Inc.
- Page 5 Using the plate as a template, drill 9/64in. (0.140 in.) holes in the icemaker base, as shown in Figure 12. CAUTION: Be careful not to drill too deep and/or too fast into the icemaker base and dispenser wrapper as damage may occur to unseen parts. © 2008, IMI Cornelius Inc. Icemaker & Adaptor Hold-Down Kit Installation Instructions Figure 9...
- Page 6 CAUTION: Be careful not to drill too deep and/or too fast into the dispenser wrapper as damage may occur to unseen parts. Publication Number: 629096853INS Figure 12 -30 I CEMAKER Table 4 Description Figure 13 - 6 - – IDC S ERIES NITS Qty. © 2008, IMI Cornelius Inc.
- Page 7 620053923 Right Side Adapter Hold-Down Bracket Using the supplied silicone tube, seal icemaker all around to the adapter top, as shown in Figure 15. © 2008, IMI Cornelius Inc. Icemaker & Adaptor Hold-Down Kit Installation Instructions Figure 14 – IDC S...
- Page 8 CAUTION: Be careful not to drill too deep and/or too fast into the icemaker base and dispenser wrapper as damage may occur to unseen parts. Publication Number: 629096853INS Figure 15 Figure 16 Figure 17 - 8 - 3/4 in. © 2008, IMI Cornelius Inc.
- Page 9 Using the supplied sheetmetal screws, screw four (4) screws per plate into the dispenser wrapper and icemaker base. Repeat Steps 1 through 5 on the other side of the dispenser. © 2008, IMI Cornelius Inc. Icemaker & Adaptor Hold-Down Kit Installation Instructions - 9 -...