Table of Contents
Advertisement
Quick Links
1. IMPORTANT SAFETY INSTRUCTIONS ................................................................................. 4
2. COOKTOP MEASUREMENTS ............................................................................................... 5
3. POSITIONING THE COOKTOP AND LOCATION REQUIREMENTS .................................... 6
3.1 Type A installation measurements (Empty base) ............................................................................................ 7
3.2 Type B installation measurements (Complete base) ...................................................................................... 8
3.3 Gas supply requirements .............................................................................................................................. 10
3.4 Electrical requirements .................................................................................................................................. 11
4. INSTALLING THE COOKTOP ............................................................................................... 13
5. CHECKING OPERATION ...................................................................................................... 16
6. WIRING DIAGRAMS ............................................................................................................. 17
WARNING: For your safety, the information in this manual must be followed to minimize the risk
of fire or explosion, or to prevent property damage, personal injury or death.
Do not store or use gasoline or other flammable vapors and liquids near this or any other
appliance.
•
Do not attempt to switch on any appliances.
•
Do not touch any electrical switches.
•
Do not use any telephones in your building.
•
Immediately call your gas supplier from a neighbor's phone. Follow the gas supplier's instructions.
•
lf you cannot reach your gas supplier, call the fire department.
Installation and service must be performed by a qualified installer, service agency or the gas supplier.
INSTRUCTIONS FOR THE INSTALLER: these are intended for the qualified engineer who is able to
install, commission and test the appliance
Table of Contents
WHAT TO DO IF YOU SMELL GAS
3
Advertisement
Table of Contents
Related Manuals for Smeg PS9RU3
Summary of Contents for Smeg PS9RU3
-
Page 1: Table Of Contents
1. IMPORTANT SAFETY INSTRUCTIONS ... 4 2. COOKTOP MEASUREMENTS ... 5 3. POSITIONING THE COOKTOP AND LOCATION REQUIREMENTS ... 6 3.1 Type A installation measurements (Empty base) ... 7 3.2 Type B installation measurements (Complete base) ... 8 3.3 Gas supply requirements ... 10 3.4 Electrical requirements ... -
Page 2: Important Safety Instructions
1. IMPORTANT SAFETY INSTRUCTIONS READ AND SAVE THESE INSTRUCTIONS – Your safety and the safety of others are very important. We have provided many important safety messages throughout this manual and on the appliance. Read all instructions before using the appliance and always obey all safety messages. RECOGNIZE SAFETY INFORMATION This is a safety alert symbol. -
Page 3: Cooktop Measurements
Instructions for the Installer 2. COOKTOP MEASUREMENTS... -
Page 4: Positioning The Cooktop And Location Requirements
3. POSITIONING THE COOKTOP AND LOCATION REQUIREMENTS NOTE: The following operation requires construction and/or carpentry work and must therefore be carried out by a competent technician. The cooktop may be installed on various materials, such as masonry, metal, solid wood, plastic laminated wood etc. -
Page 5: Type A Installation Measurements (Empty Base)
3.1 Type A installation measurements (Empty base) DISTANCES 866 mm 580 mm MINIMUM ” 866 mm 600 mm MAXIMUM ” The support strips appliance. Gas line opening Wall: everywhere, 5” (12.7 cm) beneath the underside of the countertop. Cabinet base: everywhere, within 6” (15.2 cm) from the rear wall is recommended. Grounded outlet Position within 24”... -
Page 6: Type B Installation Measurements (Complete Base)
3.2 Type B installation measurements (Complete base) Instructions for the Installer... - Page 7 Instructions for the Installer DISTANCES 580 mm MINIMUM ” 600 mm MAXIMUM ” CABINET BASE: Make two openings in the back of base that have the dimensions given alongside. The left opening will be used for the passing of the gas connection, while the right opening is for the electric connection.
-
Page 8: Gas Supply Requirements
3.3 Gas supply requirements WARNING NOTE: - Observe all governing codes and ordinances. - The cooktop must be connected to a regular gas supply. This installation must conform with all local codes and ordinances. In the absence of local codes, installation must conform with American National Standard, National Fuel Gas Code ANSI Z223.1 - latest edition or CAN/CGA B149 - latest edition. -
Page 9: Electrical Requirements
The regulator must be checked at a minimum water column of at least 1” W.C. above the set pressure. The inlet pressure to the regulator should be as follows for operation and checking the regulator setting: - NATURAL GAS: Set pressure at 4”... - Page 10 Instructions for the Installer 3.4.1 Recommended Grounding Method For your personal safety, this cooktop must be grounded. This cooktop is equipped with a 3-prong ground plug. To minimize possible shock hazard, the cord must be plugged into a mating 3-prong ground-type outlet, grounded in accordance with the National ANSI/NFPA 70 Electrical Code (latest edition*) or the Canadian Electrical Code (CSA)** and local codes and ordinances.
-
Page 11: Installing The Cooktop
4. INSTALLING THE COOKTOP Remove the styrofoam protection and lift the cooktop in order to extract it from the side protectors and the box. Connection to the gas mains should be made with a flexible metal pipe and conforming to the provisions defined by the current standard regulations in force. - Page 12 FASTENING FOR TYPE A INSTALLATION: After cooktop positioned, overlap brackets (per underneath the cooktop (B). Tighten the fastening screws (C) provided to the support strips so that once they are tightened, the cooktop is securely fastened to the structure. NOTE: Use all of the brackets supplied with the appliance to fasten it to the support structure.
- Page 13 Use a pipe-joint compound made for use with NATURAL and L.P. gas. lf a flexible metal pipe is used, make sure that the tubing is not kinked. Always use a pipe-joint compound made for use with NATURAL GAS and L.P. GAS between pressure regulator F and adaptor E and between pressure regulator F and pipe G.
-
Page 14: Checking Operation
5. CHECKING OPERATION After having fastened the top to the support structure, some simple procedures are required in order to check that it works properly. Check for any gas leaks near the cooktop connector, the pressure regulator and the safety valve. WARNING NOTE: The regulator is fitted with a checkpoint outlet gas pressure to check the exact pressure supplied to the appliance. -
Page 15: Wiring Diagrams
Instructions for the Installer 6. WIRING DIAGRAMS The power cord on this appliance is equipped with a three pronge polarized plug (grounding) which fits in standard three pronged (grounding) wall outlets. When servicing the controls, label all wires prior to disconnection. WARNING Wiring errors can cause improper and dangerous operation.