Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for aguri SKYWAY GTX90
Summary of Contents for aguri SKYWAY GTX90
- Page 1 SKYWAY | GTX90 User Manual www.aguriworld.co.uk...
-
Page 2: Table Of Contents
Contents What’s in the box? Geo Radar alerts Product overview Directional alerts Standby screen explained User POI. Add you own user point alerts Installing your Skyway on the windscreen How to delete your user point alerts Installing your Skyway using the sticky pad dash mount Set audible alerts Connecting to power... -
Page 3: What's In The Box
What’s in the box? 1 x Aguri Skyway GTX90 1 x Windscreen bracket 1 x 12V cigarette lighter power cable 1 x USB data cable 1 x 12V hard-wire lead 1 x User guide 1 x Sticky pad dash mount Please note that you must power your Skyway with the 12V cigarette lighter cable or the 12V hard-wire lead provided. -
Page 4: Product Overview
Product overview 1. DC Power in. 9. Long press Menu button to enter and exit settings menu. 2. On/Off/Volume control. Short press Menu button to 3. Radar receiver. adjust brightness in standby 4. Press to release windscreen mode. bracket. 10. Short press to temporarily 5. -
Page 5: Standby Screen Explained
Standby screen explained GPS status - connected Smart mode GPS clock Your speed Installing your Skyway on the windscreen Attach the windscreen bracket by sliding it into the slot on the rear of the unit. (Attach the suction cups if they are not already attached) Using the suction cup bracket, mount your Skyway in a safe and convenient position in the front windscreen where it has an unobstructed view of the road ahead. -
Page 6: Installing Your Skyway Using The Sticky Pad Dash Mount
Installing your Skyway using the sticky pad dash mount The sticky pad can be attached, removed, and reattached many times without losing its adhesion, and should be safe to use on most surfaces but please check before use. Find a flat location on your dashboard where you can mount your Skyway in a safe and convenient position and where it has an unobstructed view of the road ahead. -
Page 7: Installation Tips
Installation tips Before mounting your Skyway, clean the area of the windscreen where you have chosen to mount your unit, with a good quality glass cleaner to ensure the suction cup bracket makes a good contact. Remember to mount the unit and install the power cable safely in a location where it does not interfere with the driver or the controls of the vehicle. -
Page 8: Menu Settings
Menu settings Speed trap alert settings It is possible to switch individual radar frequencies and speed traps on and off, to fine tune Skyway to the country you are driving in. Enter the settings menu by pressing and holding the ‘Menu’ button. Scroll left or right, using the ‘Mute’... - Page 9 Using Skyway in other countries outside of the UK. Below are the speed trap alert settings we would recommend for a selection of other countries if you want to use your Skyway outside of the UK. Germany/Austria Spain/Portugal Italy Radar/laser Radar/laser Radar/laser alert settings...
-
Page 10: Brightness Control
Brightness control You can choose between three levels of brightness. • 100% Brightness • 50% Brightness • Auto - 100% Brightness between 6:00 to 17:59 and 50% brightness between 18:00 and 05:59 • Dark – Stealth mode. Screen will remain black apart from one small white dot to indicate the unit is powered on and working. -
Page 11: Choose Between Radar + Gps Alerts, Gps Alerts Only Or Radar Alerts Only
Highway mode City 1 City 2 Smart mode (recommended) If Smart mode is selected, your Skyway will start in City 2 up to 20mph, then switch to City 1 between 20mph and 30mph and will then automatically switch to Highway mode when you exceed 30mph. Please note that the Smart mode icon will continue to be displayed regardless of the operation mode running. -
Page 12: Vehicle Low Battery Warning
Vehicle low battery warning Your Skyway GTX90 will automatically alert you if your vehicles battery drops below 10.5V and needs recharging. Factory reset Press and hold the Menu, Mute and City buttons simultaneously until the OLED displays ‘Factory reset’. Performing a factory reset will return the unit to it’s original factory settings. -
Page 13: Directional Alerts
Directional alerts Use this setting to determine whether you get alerts to GPS speed camera traps in both directions or just the direction of operation. Switch off to get alerts in both direction and switch on to only get alerts in the direction of operation. Enter the settings menu by pressing and holding the ‘Menu’... -
Page 14: How To Delete Your User Point Alerts
POI you want to delete. The display will confirm that the user point has been deleted successfully. User note. It is also possible to manage your user points using the Skyway GTX90 updater. Please see instructions later on in this manual. Set audible alerts Use this setting to choose between the following audible alerts:- •... -
Page 15: Automute Time
Automute time Select how long you want the unit to alert at full volume before automatically reducing to your chosen muted volume. Enter the settings menu by pressing and holding the ‘Menu’ button. Scroll left or right, using the ‘Mute’ or ‘City’ buttons, until you highlight the feature graphic above and press the ‘Menu’... -
Page 16: City Smart Mute
the ‘Mute’ or ‘City’ buttons to select the speed level you require and press the ‘Menu’ button to confirm your selection and return to the menu. Press and hold the menu button to return to the standby screen or wait a few seconds and your Skyway will return to the standby screen automatically. -
Page 17: Select Preferred Speed Unit
Select preferred speed unit Use this feature to switch between MPH and KMH. Enter the settings menu by pressing and holding the ‘Menu’ button. Scroll left or right, using the ‘Mute’ or ‘City’ buttons, until you highlight the feature graphic above and press the ‘Menu’ button to select it. Use the ‘Mute’... -
Page 18: Gps Speed Calibration
increments and press the ‘Menu’ button to confirm your selection and return to the menu. Press and hold the menu button to return to the standby screen or wait a few seconds and your Skyway will return to the standby screen automatically. GPS speed calibration Use this feature to adjust the GPS speed displayed on your Skyway so that it matches the speed displayed on... -
Page 19: Gps And Radar/Laser Speed Trap Alert Screens Explained
GPS and Radar/Laser speed trap alert screens explained Speed trap alert for fixed roadside speed traps such as HADECs 3 Smart Motorway cameras, Gatso cameras and Truvelo cameras. Speed limit (Background switches to white if you Driving mode are exceeding the limit) selected GPS - connected (Smart mode) - Page 20 SPECs average speed camera – alert start Speed limit (Background switches to white if you are Driving mode exceeding the limit) selected (City 1) GPS - connected Your speed SPECs Average speed Distance to 1st camera camera detected in the sequence SPECs average speed camera –...
- Page 21 Mobile speed trap/police laser van location alert Speed limit (Background switches to white if you are Driving mode exceeding the limit) selected (City 2) GPS - connected Mobile speed trap/ police laser van Distance to speed trap Your current speed location detected Radar alert (Please note that you may also detect...
-
Page 22: How To Install The Drivers Required To Connect Your Skyway To Your Pc And Update The Software And Speed Camera Database
PC and update the software and speed camera database. Please note you may not need a Driver if you have Windows 11 installed but if your Skyway GTX90 will not connect to your PC, please use the Windows 10 Driver. Install the Driver. - Page 23 3. Double left click on folder “Skyway GTX90 Drivers”, then check the Windows SW specifications of your computer and install the correct driver. E.g., If your computers Window Specification is Window 10 Pro (64 bit Double left click “Win 10 driver => win10_x64” as below image and...
- Page 24 How to update the software and speed camera database. Once you have successfully installed the Drivers you can now update the software and speed trap database on your Aguri Skyway GTX90. 1. Download “Skyway GTX90 software and speed trap database up- dater”...
- Page 25 7. Click on the ‘Update’ tab when it appears and wait while the updater software checks the server for the latest software updates. 8. Check the ‘Status’ column to see if any updates are available and press ‘Click here to update’. 9.
- Page 26 Changing the menu settings using the Skyway GTX90 updater You can also use the updater software to change some of the unit settings. Click on the ‘Setup’ tab and then click on the settings you want to change. Once you have made the changes you want to make, press the ‘Load’...
-
Page 27: Warranty
Please note that to receive technical support or service under warranty, you must first register your unit at www.aguriworld.co.uk Having a problem with your Aguri Skyway GTX90 speed trap detector? Try visiting the FAQ section at www.aguriworld.co.uk. We find that most issues can be resolved there. - Page 28 www.aguriworld.co.uk...