Advertisement
Quick Links
Owner's Manual & Safety Instructions
Save This Manual
operating, inspection, maintenance and cleaning procedures. Write the product's serial number in the
back of the manual (or month and year of purchase if product has no number). Keep this manual and the
receipt in a safe and dry place for future reference.
VARIABLE SPEED
COMPACT ROUTER
email our technical support at: productsupport@harborfreight.com
When unpacking, make sure that the product is intact
and undamaged. If any parts are missing or broken,
please call 1‑888‑866‑5797 as soon as possible.
©
Copyright
2023 by Harbor Freight Tools
No portion of this manual or any artwork contained herein may be reproduced in
any shape or form without the express written consent of Harbor Freight Tools.
Diagrams within this manual may not be drawn proportionally. Due to continuing
improvements, actual product may differ slightly from the product described herein.
Tools required for assembly and service may not be included.
Keep this manual for the safety warnings and precautions, assembly,
Visit our website at: http://www.harborfreight.com
®
. All rights reserved.
23121E-B
Read this material before using this product.
Failure to do so can result in serious injury.
SAVE THIS MANUAL.
23h
58253
Advertisement
Related Manuals for Bauer 23121E-B
Summary of Contents for Bauer 23121E-B
- Page 1 Write the product’s serial number in the back of the manual (or month and year of purchase if product has no number). Keep this manual and the receipt in a safe and dry place for future reference. 23121E-B VARIABLE SPEED COMPACT ROUTER Visit our website at: http://www.harborfreight.com...
-
Page 2: Table Of Contents
table of contents Safety ................2 Operation ..............8 Specifications ............7 Maintenance .............12 Setup .................7 Warranty ..............15 WarninG SyMBOLS anD DeFinitiOnS This is the safety alert symbol. It is used to alert you to potential personal injury hazards. Obey all safety messages that follow this symbol to avoid possible injury or death. -
Page 3: Safety
c. Do not expose power tools to rain or wet i. Only use safety equipment that has been conditions. Water entering a power tool approved by an appropriate standards agency. will increase the risk of electric shock. Unapproved safety equipment may not provide adequate protection. - Page 4 c. Disconnect the plug from the power b. use clamps or another practical way source and/or remove the battery pack, to secure and support the workpiece if detachable, from the power tool before to a stable platform. Holding the work making any adjustments, changing by your hand or against the body leaves it accessories, or storing power tools.
- Page 5 Grounding tO preVent eLectric SHOcK anD DeatH FrOM incOrrect GrOunDinG Wire cOnnectiOn: check with a qualified electrician if you are in doubt as to whether the outlet is properly grounded. Do not modify the power cord plug provided with the tool. never remove the grounding prong from the plug.
- Page 6 extension cords 1. Grounded tools require a three wire extension cord. 7. Make sure the extension cord is properly wired Double Insulated tools can use either and in good electrical condition. Always replace a two or three wire extension cord. a damaged extension cord or have it repaired by a qualified electrician before using it.
-
Page 7: Specifications
Specifications Electrical Rating 120V~ / 60Hz / 6.5A No Load Speed : 10000 – 3 0000/min Collet Size Ø1/4" Max. Accessory Diameter 1‑3/8" Setup - Before use: read the entire iMpOrtant SaFety inFOrMatiOn section at the beginning of this manual including all text under subheadings therein before set up or use of this product. -
Page 8: Operation
Operating instructions read the entire iMpOrtant SaFety inFOrMatiOn section at the beginning of this manual including all text under subheadings therein before set up or use of this product. tO preVent SeriOuS inJury FrOM acciDentaL OperatiOn: Make sure that the power Switch is in the off-position and unplug the tool from its electrical outlet before performing any procedure in this section. - Page 9 Set up temporary Guide Clamp a temporary guide to the workpiece to make a straight cut which is not parallel to edge of workpiece. 1. Clamp a suitable straight board across workpiece parallel to desired location of cut. 2. Loosen Edge Guide Knob, then install Edge Guide with Fence facing outward and up.
- Page 10 circle cutting Use the center hole in the Fence as a pivot point when cutting circles. 1. Install Fence according to Set Up Temporary Guide on page 9. 2. Loosen Fence Knob, set distance from center hole in Fence to far edge of bit, equal to radius of circle. edge Guide 3.
- Page 11 General Operating instructions 1. Mark cut line on workpiece. 8. The bit rotates clockwise. Adjust for this while cutting: 2. Turn Power Switch off, then plug Power Cord into a. For most materials it is best to move the Router the nearest 120VAC, grounded electrical outlet.
-
Page 12: Maintenance
Maintenance and Servicing procedures not specifically explained in this manual must be performed only by a qualified technician. tO preVent SeriOuS inJury FrOM acciDentaL OperatiOn: Make sure that the power Switch is in the off-position and unplug the tool from its electrical outlet before performing any procedure in this section. - Page 13 troubleshooting problem possible causes Likely Solutions Tool will not start. 1. Cord not connected. 1. Check that cord is plugged in. 2. No power at outlet. 2. Check power at outlet. If outlet is unpowered, turn off tool and check circuit breaker. If breaker is tripped, make sure circuit is right capacity for tool and circuit has no other loads.
- Page 14 record product’s Serial number Here: note: if product has no serial number, record month and year of purchase instead. note: Replacement parts may be available for this item. Visit harborfreight.com/parts for a list of in stock parts. Reference UPC 1 93175523242. Page 14 For technical questions, please call 1-888-866-5797.
-
Page 15: Warranty
Limited 90 Day Warranty Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and durability standards, and warrants to the original purchaser that this product is free from defects in materials and workmanship for the period of 90 days from the date of purchase. This warranty does not apply to damage due directly or indirectly, to misuse, abuse, negligence or accidents, repairs or alterations outside our facilities, criminal activity, improper installation, normal wear and tear, or to lack of maintenance. - Page 16 26677 agoura road • calabasas, ca 91302 • 1-888-866-5797...