Table of Contents
Advertisement
Changing the basic settings
Your oven has various basic settings. These settings can be
customised to suit your requirements.
Basic setting
Selection 1 Selection 2 Selection 3
c1 Clock display
always*
c2 Signal duration
approx.
upon completion of
10 seconds
a cooking time or
timer period
c3 Waiting time until a
approx.
setting is applied
2 seconds
* Factory setting
Cleaning system
The cleaning system regenerates the self-cleaning surfaces in
the cooking compartment.
The back wall, ceiling and side walls of the cooking
compartment are coated with a highly porous ceramic layer.
This coating absorbs and disintegrates splashes from baking
and roasting while the oven is in operation. If these self-
cleaning surfaces no longer clean themselves adequately, they
can be regenerated with the cleaning system.
Before cleaning
Remove accessories and cookware from the cooking
compartment.
Cleaning the cooking compartment floor
Before you set the cleaning system, clean the surfaces in the
cooking compartment that are not self-cleaning. Otherwise,
stains will develop that it is not possible to remove.
Use a dish cloth and hot soapy water or a vinegar solution. If
there are heavy deposits of dirt, use a stainless steel scouring
pad or oven cleaner. Only use when the cooking compartment
is cold. Never treat the self-cleaning surfaces with a scouring
pad or oven cleaner.
Making settings
Cleaning takes approximately one hour.
Set the function selector to
1.
Set the temperature selector to
2.
Press the
button.
u
3.
Care and cleaning
With good care and cleaning, your oven will remain clean and
fully-functioning for a long time to come. Here we will explain
how to maintain and clean your oven correctly.
Notes
Slight differences in the colours on the front of the oven are
■
caused by the use of different materials, such as glass,
plastic and metal.
12
only with
-
the
but-
0
ton
approx.
approx.
2 minutes*
5 minutes
approx.
approx.
5 seconds*
10 seconds
3D hot air.
<
.
s
No other time-setting option should have been set.
Press and hold the
0
button for approx. 4 seconds.
1.
The current basic setting for the clock display is shown in the
display, e.g. c1 1 for selection 1.
Use the
or
button to change the basic setting.
@
A
2.
Confirm by pressing the
3.
The next basic setting appears in the display. You can scroll
through all levels with the
with the
@
or
A
button.
To finish, press and hold the
4.
All basic settings are applied.
You may change the basic settings at any time.
The
symbol lights up in the display. The time at which the
u
cleaning will end appears and the
Cleaning will start after a few seconds. You will see the time
counting down and the
r
symbol goes out.
Cleaning is finished
A signal sounds. The oven stops heating. 00:00 is shown in the
display. Press the
button twice and turn the function selector
0
to the off position. The oven switches off.
Cancelling cleaning
Press the
button and turn the function selector to the off
u
position. The oven switches off.
Setting a later end time
You can delay the time at which the cleaning programme is due
to finish. For instance, you can set the cleaning programme to
run at night so that you can use your oven during the day.
Make the settings as described in steps 1 to 3. Before cleaning
starts, use the
or
button to set a later end time.
@
A
The oven switches to standby. The display shows the time at
which the cleaning will finish and the
When cleaning starts, you can see the time counting down in
the display and the
r
symbol is in brackets. The
goes out.
After cleaning
When the cooking compartment has cooled down completely,
wipe the salt residues off the self-cleaning surfaces with a
damp cloth.
Shadows on the door panel which look like streaks, are
■
caused by reflections made by the oven light.
Enamel is baked on at very high temperatures. This can
■
cause some slight colour variations. This is normal and does
not affect their function. The edges of thin trays cannot be
completely enamelled. As a result, these edges can be
rough. This will not impair the anti-corrosion protection.
0
button.
button and change the setting
0
button for approx. 4 seconds.
0
symbol is in brackets.
p
symbol will be in brackets. The
p
symbol is in brackets.
p
p
symbol
Advertisement
Table of Contents
