Table of Contents
Advertisement
The appliance is at temperature when the main screen (home-
page) appears.
7. TURNING THE APPLIANCE OFF
Whenever the coffee machine is turned off after being used to
make coffee, it performs an automatic rinse cycle.
Danger of burns!
During rinsing, a little hot water flows from the coffee spouts
(A8). Avoid contact with splashes of water.
•
To turn the appliance off, press the
9).
•
The message "TURNING OFF UNDERWAY, PLEASE WAIT"
is displayed, then the appliance performs a rinse cycle and
goes off (standby).
Please note!
If you will not be using the appliance for some time, unplug
from the mains socket:
•
first turn the appliance off by pressing the
(fig. 9);
•
release the main switch (A21) at the back of the appliance
(fig. 2).
Important!
Never press the main switch while the appliance is on.
8.
MENU SETTINGS
8.1
Rinsing
Use this function to deliver hot water from the coffee spouts
(A8) and hot water/steam spout (C6), if inserted, to clean and
heat the appliance's internal circuit.
Place a container with a minimum capacity of 100ml under the
coffee and hot water spouts (fig. 8).
To enable the function, proceed as follows:
1. Press the selection arrow (B2) corresponding to the "
symbol (B8) to enter the menu;
2. Press the selection arrow corresponding to "
Important! Danger of burns.
Do not leave the appliance unattended while hot water is being
delivered.
3. After a few seconds, hot water is delivered first from the
coffee spouts, then from the hot water/steam spout (if in-
serted) to clean and heat the appliance's internal circuit.
"RINSING UNDERWAY, HOT WATER FROM SPOUTS" appears
on the display, together with a progress bar which fills
gradually as preparation proceeds;
4. To interrupt rinsing, press the selection arrow correspond-
ing to " STOP" or wait for rinsing to stop automatically.
Please note!
•
•
8.2 Descaling
For instructions on descaling, see section "16.
8.3 Water filter
For instructions on how to install the filter (C4), see section"18.
button (A7) (fig.
Water softener filter".
8.4 Beverages settings
In this section, you can consult your customised settings and, if
you wish, reset the default values for each beverage.
1. Press the selection arrow (B2) corresponding to the "
2. Scroll through the menu items by pressing the selection
button
3. The values for the first beverage appear on the display;
4. The reference user profile is highlighted on the display. The
5. To go back to the settings menu, press the selection arrow
6. To reset the default values for the beverage displayed,
7. "CONFIRM RESET?": to confirm press the selection arrow
"
8. "DEFAULT VALUES SET": press " OK".
The beverage has been reset to the default values. Proceed with
RINSING";
the other beverages or go back to the homepage by pressing the
arrow corresponding to "
•
•
8.5 Adjust time
To adjust the time on the display (B1), proceed as follows:
1. Press the selection arrow (B2) corresponding to the "
11
If the appliance is not used for more than 3-4 days, when
switched on again, we strongly recommend performing
2/3 rinses before use;
After cleaning, it is normal for the coffee grounds container
(A10) to contain water.
symbol (B8) to enter the menu;
arrow corresponding to "NEXT>" until "
SETTINGS" appears on the display;
values are displayed on vertical bars. The default value is
indicated by the
symbol, while the current value is
highlighted by the solid part of the vertical bar;
corresponding to "
ESC". To scroll through and display
the beverages, press the selection arrow corresponding to
"NEXT>";
press the selection arrow corresponding to "
corresponding to " OK" (to cancel, press the selection
arrow corresponding to "
ESC" twice.
Please note!
To change the beverages in another profile, go back to the
homepage, select the required profile (B11) and repeat the
procedure.
To reset all the beverages in the profile to the default val-
ues, see section "8.16 Valori di fabbrica".
symbol (B8) to enter the menu;
Descaling".
BEVERAGES
RESET";
ESC");
"
"
Advertisement
Table of Contents
Troubleshooting
