Table of Contents
Advertisement
Unplug this apparatus during lightning storms or when unused
for long periods of time.
Refer all servicing to qualified service personnel. Servicing
is
required when the apparatus has been damaged in any way,
such as power supply cord or plug is damaged, liquid has been
spilled or objects have fallen into the
apparatus,
the apparatus
has been exposed to rain or
moisture,
does not operate normally,
or has been dropped.
The apparatus should be used in non-tropical climate.
The ventilation should not be impeded by covering the ventilation
openings with items, such as newspapers, tablecloths, curtains, etc.
No naked flame sources, such as
lighted
candles, should
be
placed on the apparatus.
Touching uninsulated terminals or wiring
may
result in an
unpleasant sensation.
You must allow a minimum 10 cm or 4 inches of unobstructed
clearance around the unit.
WARNING:
The rear panel power cord connector is the mains
power disconnect device. The device must be located in an open
area that allows access to
the
cord connector.
The unit must be connected to a
power
supply only of the type
and voltage specified on the rear panel. (USA:
120
V
/
60Hz,
EC: 230V/50Hz)
CAUTION:
The rear panel includes an AC voltage selection
switch. Confirm this switch is set to
the
proper AC voltage before
attaching
the power cord.
Connect the component to the power outlet only with the supplied
power supply cable or an exact equivalent. Do not modify the
supplied cable. Do not use extension cords.
The
mains
plug is the disconnect of the unit. In order to completely
disconnect
the unit from the supply mains, remove the main
plug
from
the
unit and the AC power
outlet.
This is the only way to
completely remove mains power from the unit.
Use Class 2 wiring for speaker connections to ensure proper
installation and minimize the risk of electrical shock.
The
batteries
in
the remote control should not be exposed to
excessive temperature such as sunshine, fire or other heat
sources. Batteries should be recycled or disposed as per state
and local guidelines.
WARNING:
The
master power switch is located on the rear panel.
The unit must allow unobstructed access to the main power switch.
FCC Information
This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the
FCC
Rules.
These limits
are
designed to provide reasonable protection against
harmful interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy and, if
not installed and used in accordance with the
instruction,
may
cause harmful interference to radio communications.
However, there is
no
guarantee that interference will not occur
in
a particular installation. If this equipment does cause harmful
interference
to
radio or television reception, which can be
determined by turning
the
equipment off and on, the user is
encouraged to try to correct the
interference
by one or more of
the following measures:
•
Reorient or relocate the receiving antenna. {TV, radio, etc.).
•
Increase the separation between the equipment and receiver.
•
Connect the equipment to an outlet on circuit different from that
to which the receiver is connected.
•
Consult the dealer or an experienced radio/TV technician for
additional help.
Caution
This device complies with part 15 of the FCC Rules. Operation
is
subject to the following to conditions: ( 1) This device may not
cause harmful interference, and (2) this device must accept any
interference received, including interference that
may
cause
undesired operation.
NOTE TO CATV SYSTEM INSTAllfR:
Call the CATV system or antenna
installer's attention to Article 820-40 of the NEC. This provides
guidelines for proper grounding and, in particular, specifies that
the cable ground shall be connected to the grounding system of
the building, as close to the point of
cable
entry as practical.
See installation diagram.
NOTE:
This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant to Part 15 of
the FCC Rules. These limits are designed to provide reasonable
protection against interference
in
a residential installation. This
equipment generates and can radiate radio frequency energy
3
and, if not installed and used in accordance with
the
instructions,
may cause interference to
radio
or TV communications. There
is no guarantee that interference will not occur in a particular
installation.
If this equipment does cause interference to radio
or television
reception,
which can be
determined
by turning the
equipment off and on, try
to
correct the interference by one or
more of the following measures:
•
Reorient or relocate
the
receiving antenna.
•
Increase the separation between the unit and the television tuner.
•
Connect the unit to an AC power outlet on a different electrical
circuit.
•
Consult your authorized Rotel retailer for assistance.
ANTENNA GROUNDING ACCORDING TO
NATIONAL
ELECTRICAL CODE INSTRUCTIONS
SECTION 810:
"RADtO
AND TELEVISION EQUIPMENT"
Advertisement
Table of Contents
