Cavius 2203-002 User Manual

MAINS
POWERED
SMOKE ALARM
PLEASE READ THE USER GUIDE
CAREFULLY BEFORE INSTALLATION
AND RETAIN FOR FUTURE USE.
CHAMBER
FILTER
OPTIONAL HOLE
FOR LAMP WIRE
TEST BUTTON
SIREN
1. HOW TO SET UP AND CONNECT ALARMS:
Start by pulling out the battery isolation strip in the
battery compartment as shown.
Please note: RF connection is done with the
device powered with battery only. You do not have
to connect the power supply unit. The product
label must not be removed as it contains important
information regarding the product.
back of the alarm to the 'Learn Mode' position.
Please note: The learn switch placed on the back
of the alarm can only be in learn position when the
alarm is disassembled from the power supply unit.
The learn switch will automatically switch to normal
position when the alarm head is fitted to the power
supply unit.
The red LED will light up to indicate that 'Learn
2. THE BEST AREAS TO INSTALL
THE SMOKE ALARM:
• Note the local country regulations regarding
installation and compliance.
• Note the local regulations and information for
insurance company policy regarding installed
smoke alarms.
• Install an alarm between possible fire sources and
bedrooms as a minimum.
• Install alarms on each floor of the house, in
hallways and stairways.
• Alarms in each room such as bedrooms and living
rooms.
Additional alarms increase the security.
CAVIUS Mains Powered Photoelectric Smoke Alarm
Part Code: 2901 CAVMPRK
Model: 2203-002
This smoke alarm is designed for private homes.
TECHNICAL INFORMATION
The smoke alarm is powered by mains power (110-
230V AC), with a lithium CR2 back-up battery.
It can be Radio Frequency (RF) interconnected with
other 2203 CAVMP alarms and CAVIUS™ Wireless
Family battery-operated alarms. The maximum
number of alarms that can be interconnected within
a house group are 32.
Our Mains Powered alarms can only interconnect
via radio frequency technology. There are no
terminals to interconnect together with cable.
Please note: These must be alarms from the
CAVIUS™ Wireless Family range.
The distance between interconnected alarms
depends on the house layout and they should
always be tested after installation. It is not advised
to install alarms with a separation of more than 10m.
RED & GREEN LED
ISOLATION
STRIP
All alarms to be connected in the house should be
put into 'Learn Mode' by sliding the switch on the
Mode' has been selected.
Do not remove the battery during 'Learn Mode' as
this will interrupt the learn process. Press and hold
the test button on one alarm only, until it beeps and
the LED flashes. This alarm will become the master
and will start sending out a specific house code to
the other alarms.
1
Diameter: 97mm. Height: 41mm (without mounting
base) 52mm (with mounting base).
Radio Frequency: 926.365 MHz
Complies to standards: AS3786:2014
Do not paint the alarm.
Disposal: For battery and product, please dispose
properly at the end of life. This is electronic waste
which should be recycled at an authorised e-waste
facility.
WARNING: Please remove dust cover after
installation. Smoke will not be able to reach the
chamber while the dust cover is in place.
All Rights Reserved: CAVIUS™ Aps assumes no
responsibility for any errors, which may appear in
this manual. Furthermore, CAVIUS™ Aps reserves
the right to alter the hardware, software, and/or
specifications detailed herein at any time without
notice, and CAVIUS™ Aps does not make any
commitment to update the information contained
herein. All the trademarks listed herein are owned by
their respective owners.
1
As the other alarms receive the specific house code,
they will also flash the LED light.
2
When all alarms flash the red LED, they are
connected and can be switched out of 'Learn
Mode' and installed.
3. AREAS WHERE NOT
TO INSTALL SMOKE ALARMS:
• In dusty rooms
• At the top of a high pointed ceiling, in ceiling
corners, and within 50cm of a wall.
• In rooms where temperature goes outside the
range +4° to 38°C or above 90% relative humidity
not condensing.
• In kitchens, garages, laundries, or too close to
fireplaces; areas where either dampness, gases or
smoke could occur.
Place the alarm where it is reachable in order to test
the alarm and for maintenance.
NORMAL MODE
LEARN MODE
2
1