Table of Contents
Advertisement
•
To select forward rotation (clockwise), release the trigger
and slide the forward/reverse switch
the tool in a counterclockwise direction.
•
To select reverse rotation (counterclockwise), release the
trigger and slide the forward/reverse switch
of the tool in a clockwise direction.
nOTE: The first time the tool is run after changing the direction
of rotation, you may hear a click on start‑up. This is normal and
does not indicate a problem.
Lock‑off Button (Fig. A)
To lock the tool, slide the lock‑off button
position. When the lock‑off button is in the locked position, the
tool is locked and the trigger switch
Worklight (Fig. A)
There is a worklight
located on the foot of the tool. The
6
worklight is activated when the trigger switch is depressed.
When the trigger is released, the worklight will stay illuminated
for up to 20 seconds.
nOTE: The worklight is for lighting the immediate work surface
and is not intended to be used as a flashlight.
Usage (Fig. A, D)
WARNING: To reduce the risk of serious personal
injury, turn unit off and remove the battery pack
before making any adjustments or removing/
installing attachments or accessories. An accidental
start‑up can cause injury.
WARNING: The ratchet may stall if overloaded, causing
a sudden twist. Always expect the tool to twist. Grip the
ratchet firmly to control the twisting action and avoid
possible personal injury.
CAUTION: Ensure fastener and/or system will withstand
the level of torque generated by the tool. Excessive torque
may cause breakage and possible personal injury.
Cat #
DCF510
1. Install the appropriate removable anvil
the tool.
a. If an anvil is installed on the tool, push the release
button
on the backside of the tool and remove
9
the anvil.
b. To install an anvil, push the desired anvil into the tool
until it is secure.
2. Place the accessory on the fastener head.
3. Consider the intended operation and select either forward
or reverse rotation.
4. Press variable speed trigger
5. Release variable speed trigger
6. If the ratchet stalls, the tool is overloaded or is being
improperly used. Release the variable speed trigger
immediately. Do not press the variable speed trigger
and off in an attempt to start a stalled ratchet. Doing so can
damage the tool.
3
on the head of
3
on the head
8
to the locked
cannot be pulled.
1
RPM
Ft.-lbs.
0–300
75 (Max.)
101 (Max.)
2
(3/8" or 1/2") on
to start operation.
1
to stop operation.
1
7. The ratchet can also be used manually for breaking free
stubborn fasteners or snugging by releasing the trigger and
applying the torque by hand.
nOTE: Excessive manually applied torque may damage the
anvil if it exceeds the torque limit 101 Nm.
MAINTENANCE
Your power tool has been designed to operate over a long
period of time with a minimum of maintenance. Continuous
satisfactory operation depends upon proper tool care and
regular cleaning.
WARNING: To reduce the risk of serious personal
injury, turn tool off and disconnect battery pack
before making any adjustments or removing/
installing attachments or accessories. An accidental
start‑up can cause injury.
The charger and battery pack are not serviceable.
Lubrication
Your power tool requires no additional lubrication.
Cleaning
WARNING: Electrical shock and mechanical hazard.
Disconnect the electrical appliance from the power source
before cleaning.
WARNING: To ensure safe and efficient operation,
always keep the electrical appliance and the ventilation
slots clean.
WARNING: Never use solvents or other harsh chemicals
for cleaning the non‑metallic parts of the tool. These
chemicals may weaken the materials used in these parts.
Use a cloth dampened only with water and mild soap.
Never let any liquid get inside the tool; never immerse any
part of the tool into a liquid.
Ventilation slots can be cleaned using a dry, soft non‑metallic
brush and/or a suitable vacuum cleaner. Do not use water or
any cleaning solutions. Wear approved eye protection and an
nm
approved dust mask.
Optional Accessories
WARNING: Since accessories, other than those offered
by D
WALT, have not been tested with this product, use
e
of such accessories with this tool could be hazardous.
To reduce the risk of injury, only D
accessories should be used with this product.
Consult your dealer for further information on the
appropriate accessories.
Protecting the Environment
Separate collection. Products and batteries marked
with this symbol must not be disposed of with normal
w
household waste.
Products and batteries contain materials that can be
recovered or recycled, reducing the demand for raw materials.
1
Please recycle electrical products and batteries according to local
on
1
provisions. Further information is available at www.2helpU.com.
English
WALT‑recommended
e
11
Advertisement
Table of Contents
