Related Manuals for Pentair WARRIOR SI
Summary of Contents for Pentair WARRIOR SI
- Page 1 PROWLER ® (P/N 360323) WARRIOR ® (P/N 360495) ROBOTIC INGROUND POOL CLEANER INSTALLATION AND USER’S GUIDE IMPORTANT SAFETY INSTRUCTIONS READ AND FOLLOW ALL INSTRUCTIONS SAVE THESE INSTRUCTIONS...
-
Page 2: Important Warning And Safety Instructions
Can trap and tear hair or body parts. Hose can trip or finish or the vinyl liner, Pentair Aquatic Systems disclaims any liability for entangle swimmers which could result in drowning. - Page 3 IMPORTANT WARNING AND SAFETY INSTRUCTIONS Disclaimer of Liability About your Pool and Cleaner There are a multitude of factors that contribute to the life of your pool. These robotic pool cleaners are very passive products that will have no impact on pool life. Please be aware that over time, deterioration, discoloration and brittleness of any pool finish can be caused separately by, or in combination with, age, an imbalance in pool water chemistry, improper installation and other...
-
Page 4: Table Of Contents
CUSTOMER SERVICE / TECHNICAL SUPPORT If you have questions about ordering Pentair replacement parts, and pool products, please use the following contact information: Customer Service Technical Support (8 A.M. to 4:30 P.M. — Eastern and Pacific Times) Sanford, North Carolina (8 A.M. to 4:30 P.M. ET) -
Page 5: Preparation Of The Pool And Cleaner
See page 3 for Caddy Assembly instructions. The Warrior SI does not include a caddy. Position the caddy or power supply at least 12 feet (3.5 m) from the edge of the pool. See Figure 1. - Page 6 STEP 3: STEP 5: Connect Power Supply to Cleaner Placing the Cleaner in the Pool Connect the communication cable to the power supply. Do not switch the pool cleaner to “ON” if it is not Ensure the connector notch is lined up with the fully immersed in water.
-
Page 7: Caddy Assembly (Prowler 930 Only)
Caddy Assembly (Prowler 930 Only) The following section contains instructions for assembling the Prowler 930 cleaner caddy: STEP 1: STEP 3: Figure 9 Removing the Communication Cable Holder Installing the Handle Support 1. While holding the caddy chassis in place, pull the top of the communication cable holder straight out until it 1. - Page 8 STEP 5: STEP 7: Figure 12 Install the Caddy Handle Install the Power Cable Holder 1. Insert the caddy handle 1. Using the final two shorter Phillips-head screws into the handle support. provided with the caddy, secure the power cable holder See Figure 12.
-
Page 9: Operation
OPERATION Control Panel Overview 3 Schedule 2 Cleaning Bluetooth Wireless Technology ® LEDs Speed LEDs Connection Indicator Weekly Timer Cleaning On/Off Button Speed Button Button Weekly Timer Feature The power supply has a timer control that allows you to set an automatic cleaning schedule each week. Be sure the cleaner is fully immersed in water before turning on the power. -
Page 10: Bluetooth Operation
Bluetooth Operation ® The Prowler 930 and Warrior SI Robotic Inground 3. After successfully connecting your smartphone to the ® ® Pool Cleaners contain a Bluetooth Wireless Technology ® desired cleaner, the Welcome screen will display. receiver that allows the cleaner to communicate with most You’ll have three options on this screen: smartphones. -
Page 11: Maintenance
MAINTENANCE Make sure the cleaner’s power supply is turned “OFF” and is disconnected from the electrical source/outlet before servicing the cleaner. Moving parts may injure hands or fingers if cleaner inadvertently powers on during servicing. Figure 16 LED Indicator Lights The Prowler 930 and Warrior SI Robotic Pool Cleaners include an... -
Page 12: Cleaning The Filter Baskets
Cleaning the Filter Baskets Note: It is highly recommended that you clean the filter baskets after each cleaning cycle. Too much debris in the filter will restrict the suction power of the Prowler 930 or Warrior SI Robotic Pool Cleaner and reduce its effectiveness. ®... -
Page 13: Periodic Filter Screen Cleaning
Periodic Filter Screen Cleaning Note: It is recommended that you clean the filter screens at least once a month. Too much debris in the filter screens will restrict the suction power of the Prowler 930 or Warrior SI Robotic Pool Cleaner and reduce its effectiveness. ®... -
Page 14: Cleaning The Impeller
Cleaning the Impeller Always disconnect power to the cleaner before servicing, disassembly, or reassembly. Failure to do so could result in death or serious injury to servicemen, pool users or others due to electrical shock. Read all servicing instructions before servicing the cleaner. Every so often debris may become trapped in the Prowler 930 or Warrior SI Robotic Pool Cleaner’s impeller. -
Page 15: Storing The Cleaner
STEP 6: STEP 5: Remount the Intermediate Cover and Manifold Remount the Impeller Cover Assembly Gently push the impeller cover back onto the impeller assembly. See Figure 34. Reseat the intermediate cover and manifold assembly and reinstall the two screws that hold the cover and manifold The tabs on the motor unit will lock the cover into place. -
Page 16: Troubleshooting
TROUBLESHOOTING Problem Possible Cause Corrective Action Cable twisting or cable Obstruction in pool Remove obstruction in pool. coils up. Gets stuck on main drain cover Turn off filter and install main drain cover ring. Straighten cable and lay in sun periodically. Excess cable in the pool Remove excess cable from pool. -
Page 17: Replacement Parts
REPLACEMENT PARTS Item Prowler Warrior Description Part # Part # 360400 Power Supply 360446 Communication Cable 360507 Outer Filter Basket 360445 Inner Filter Basket 360363 Cartridge Filter Kit 360364 Net Filter Kit 360365 Motor Unit 360366 Front Brush Assembly 360367 Rear Brush Assembly 360370 Manifold Assembly... - Page 18 NOTES PROWLER® 930 and WARRIOR® SI Robotic Inground Pool Cleaner Installation and User’ s Guide...
- Page 19 NOTES PROWLER® 930 and WARRIOR® SI Robotic Inground Pool Cleaner Installation and User’ s Guide...
- Page 20 ® and logos are registered trademarks owned by the Bluetooth SIG, Inc. and any use of such marks by Pentair Water Pool and Spa, Inc. is under license. Other trademarks and trade names are those of their respective owners. Unless expressly noted, names and brands of third parties that may be used in this document are not used to indicate an affiliation or endorsement between the owners of these names and brands and Pentair Water Pool and Spa, Inc.