Related Manuals for Bosch MIC-7522-Z30GR
Summary of Contents for Bosch MIC-7522-Z30GR
- Page 1 MIC IP ultra 7100i │ MIC IP starlight 7100i MIC‑7504‑Z12BR│MIC‑7504‑Z120WR│MIC‑7504‑Z12GR│MIC‑752 2‑Z30B│MIC‑7522‑Z30W│MIC‑7522‑Z30G│MIC‑7522‑Z30BR│MIC ‑7522‑Z30WR│MIC‑7522‑Z30GR Installation Manual...
-
Page 3: Table Of Contents
Typical IP Configuration with High PoE midspan (no I/O connections) 15.2 Typical Configuration with MIC-ALM-WAS-24 Troubleshooting 16.1 Physical reset button Maintenance 17.1 Replacing a wiper assembly Decommissioning 18.1 Transfer 18.2 Disposal Technical data Bosch Security Systems 2022-09 | 2.1 | Installation Manual... - Page 4 | Table of contents MIC IP ultra 7100i │ MIC IP starlight 7100i Support services and Bosch Academy 2022-09 | 2.1 | Bosch Security Systems Installation Manual...
-
Page 5: Safety
Legal Information Copyright This manual is the intellectual property of Bosch Security Systems, and is protected by copyright. All rights reserved. Trademarks All hardware and software product names used in this document are likely to be registered trademarks and must be treated accordingly. -
Page 6: Safety Precautions
Notice! This symbol indicates information or a company policy that relates directly or indirectly to the safety of personnel or protection of property. 2022-09 | 2.1 | Bosch Security Systems Installation Manual... -
Page 7: Important Safety Instructions
® Electrical Code (NEC)), Canadian Electrical Code, Part I (also called CE Code or CSA C22.1), and all applicable local codes. Bosch Security Systems accepts no liability for any damages or losses caused by incorrect or improper installation. Warning! INSTALL EXTERNAL INTERCONNECTING CABLES IN ACCORDANCE TO NEC, ANSI/NFPA70 (FOR US APPLICATION) AND CANADIAN ELECTRICAL CODE, PART I, CSA C22.1 (FOR CAN... - Page 8 Do not open the camera unit. Doing so will invalidate the warranty. – Do not point the camera at the sun. Bosch Security Systems will not be liable for any damage to cameras that have been pointed directly at the sun.
-
Page 9: Important Notices
Camera signal - Protect the cable with a primary protector if the camera signal is beyond 140 feet, in accordance with NEC800 (CEC Section 60). Environmental statement - Bosch has a strong commitment towards the environment. This device has been designed to respect the environment as much as possible. - Page 10 MIC IP ultra 7100i High-definition 4K PTZ camera MIC IP starlight 7100i High-definition PTZ camera Responsible party Bosch Security Systems, Inc. 130 Perinton Parkway 14450 Fairport, NY, USA www.boschsecurity.us UL Disclaimer Underwriter Laboratories Inc. ("UL") has not tested the performance or reliability of the security or signaling aspects of this product.
-
Page 11: Important Notices - Illumination Safety
200 mm 2.19 100 s 200 mm 0.386 Infrared Hazard Hazard 279 mm Distance Retinal Blue Light 10,000 s 200 mm 22.9 100s 200 mm 0.266 Hazard Hazard 2675 mm Distance Bosch Security Systems 2022-09 | 2.1 | Installation Manual... -
Page 12: Use Latest Software
– Security advisories, that is a list of identified vulnerabilities and proposed solutions: https://www.boschsecurity.com/xc/en/support/product-security/security-advisories.html Bosch assumes no liability whatsoever for any damage caused by operating its products with outdated software components. Notice! Bosch strongly recommends upgrading to the latest firmware for the best possible functionality, compatibility, performance and security. -
Page 13: Introduction
Sales or Customer Service Representative from Bosch Security Systems. – Do not use this product if any component appears to be damaged. Please contact Bosch Security Systems in the event of damaged goods. – The original packing carton (if undamaged) is the safest container in which to transport the unit and must be used if returning the unit for service. -
Page 14: Additional Tools
If you cannot connect, the unit may have reached its maximum number of connections. Depending on the device and network configuration, each unit can have up to 50 web browser connections, or up to 100 connections via Bosch Video Client or BVMS. Password protection in camera The device is password-protected. -
Page 15: Product Description
Make sure that the installation conditions comply with the specified stresses of vibration and shock as mentioned in the datasheet. A long-life silicone wiper blade mounted on a spring-loaded arm is standard on all MIC cameras. Bosch Security Systems 2022-09 | 2.1 | Installation Manual... -
Page 16: Overview Of Installation Steps
® Electrical Code (NEC)), Canadian Electrical Code, Part I (also called CE Code or CSA C22.1), and all applicable local codes. Bosch Security Systems accepts no liability for any damages or losses caused by incorrect or improper installation. Caution! ELECTRIC SHOCK HAZARD... -
Page 17: Mounting
Mounting Mounting Location and Orientation Options Bosch designed MIC IP 7100i cameras for use in outdoor applications. In an enclosed installation area (for example, in a foundry, near a furnace, etc.), temperatures outside of the camera might exceed +65 °C (+149 °F). If you install a camera in an enclosed area, make sure that the operating temperature of the camera is a maximum of +60 °C (+140 °F). - Page 18 If the camera is installed in a highly exposed location where lightning strikes may occur, then Bosch recommends installing a separate lightning conductor within 0.5 m (1.6 ft) of the camera and at least 1.5 m (4.9 ft) higher than the camera. A good earth bonding connection to the camera housing itself will provide protection against damage from secondary strikes.
-
Page 19: Mounting Options
See the figures below for illustrations of the correct and the incorrect mounting orientations of MIC cameras. Correct mounting orientation - upright, Correct mounting orientation - canted inverted Figure 5.1: Incorrect/not permitted mounting orientations (inverted + canted, horizontal) Bosch Security Systems 2022-09 | 2.1 | Installation Manual... - Page 20 MIC IP ultra 7100i │ MIC IP starlight 7100i The figure below illustrates the tilt range of the camera in upright orientation. 90° 90° 55° 55° Figure 5.2: Tilt range, MIC IP ultra 7100i 2022-09 | 2.1 | Bosch Security Systems Installation Manual...
-
Page 21: Mounting Bracket Options
Bosch sells a complete series of mounting brackets that support multiple mounting configurations. Always use only Bosch-supplied mounts, which are designed for safe installation of your MIC camera. Refer to the MIC Series Mounting Brackets Installation Guide for complete installation instructions. -
Page 22: Considerations For Mounting The Camera In Inverted Orientation
The camera head will rotate automatically into inverted position (180°). Note the position of the visor when the camera is installed in inverted orientation. The visor will now be near the body of the camera. 2022-09 | 2.1 | Bosch Security Systems Installation Manual... - Page 23 Seal the mount so that moisture or water cannot collect and stay in the bottom of the MIC camera. The figure that follows shows the camera installed in inverted orientation on a pole. Figure 5.7: MIC camera mounted in inverted orientation (on pole) Bosch Security Systems 2022-09 | 2.1 | Installation Manual...
-
Page 24: Installing The Camera Outdoors
IP cameras, including AUTODOME and MIC. The illustration can represent any IP camera. Mounting hardware varies between units. Figure 6.1: Correct outdoor installation with proper surge/lightning suppression 2022-09 | 2.1 | Bosch Security Systems Installation Manual... - Page 25 – Follow the manufacturer’s installation instructions. Camera Housings and Mounts – Use only Bosch mounts listed on the specific camera’s data sheet. – Follow all grounding for the camera housings and mounts per the installation manual. Bosch Security Systems 2022-09 | 2.1 |...
- Page 26 Put the Ethernet cable from the output side of the surge suppressor through the parapet pipe. 10. Complete the installation of the AUTODOME pipe mount kit per sections 2.6 and 2.7 of the parapet mount installation guide. 2022-09 | 2.1 | Bosch Security Systems Installation Manual...
- Page 27 MIC IP ultra 7100i │ MIC IP starlight 7100i Installing the camera outdoors | en Figure 6.2: Grounding a parapet mount Bosch Security Systems 2022-09 | 2.1 | Installation Manual...
-
Page 28: Optional) Installing An Sd Card
If necessary, put the O-ring seal into the cover. Put on the cover. Install the two (2) fasteners that you removed in step 1. Tighten the fasteners to 1.8 N m (1.3 ft lb). 2022-09 | 2.1 | Bosch Security Systems Installation Manual... -
Page 29: Optional) Configuration Programming In The Shipping Box
3. Configure the camera. Refer to the separate User Manual for details. 4. Disconnect the wires/cables from the connectors in the base of the camera. Refer to – (Optional) Configuration Programming on a Temporary Table-top Stand, page 30 Bosch Security Systems 2022-09 | 2.1 | Installation Manual... -
Page 30: (Optional) Configuration Programming On A Temporary Table-Top Stand
Camera > Installer Menu > Orientation), then the camera head will rotate automatically into inverted position (180°). Note that the visor will now be near the body of the camera. Disconnect the wires/cables from the connectors in the base of the camera. 2022-09 | 2.1 | Bosch Security Systems Installation Manual... -
Page 31: Installing A Mic Camera On A Hinged Dca
Phillips-head screwdriver to attach ground wire * (Optional) MOLYKOTE® 111 grease [from Dow Corning] for primary O-ring Warning! Ensure not to damage the paint on the housing of the camera or the mount. Bosch Security Systems 2022-09 | 2.1 | Installation Manual... - Page 32 MIC IP ultra 7100i │ MIC IP starlight 7100i 3/4” NPT 1. Attach the DCA to the mounting location using user-supplied hardware (item 1). (Bosch recommends stainless steel bolts and washers.) 2. Attach user-supplied conduit or glands to the side hole or to the bottom hole. If applicable, use the conduit adapter (male M25 to female ¾...
- Page 33 5. Insert the O-ring (item 1). 6. Loosen the Torx bolts two (2) turns (items 2). Slide the hook up (item 3). Tighten the bolts to hold the hook in place temporarily (item 4). Bosch Security Systems 2022-09 | 2.1 | Installation Manual...
- Page 34 Fully tighten the hook bolts (item 3). 9. Carefully tilt the camera to the side with the pin under the hook. 2022-09 | 2.1 | Bosch Security Systems Installation Manual...
- Page 35 10. Make the appropriate electrical connections. Refer to the chapter Connections for more information. 11. Connect the lead from the camera pigtail to the ground post on the pan base. The connection for the customer should be to the lead from the post. Bosch Security Systems 2022-09 | 2.1 | Installation Manual...
- Page 36 17 N m (12.5 ft lb) 12. Carefully tip the camera to its final position. Avoid pinching wires between the camera base and the DCA! Insert four washers and hex bolts (supplied). 2022-09 | 2.1 | Bosch Security Systems Installation Manual...
-
Page 37: Optional) Installing A Sunshield
Discard the cut-out plastic. Note: This step does not apply to cameras mounted in inverted orientation. Remove the screws from the camera head. #2 Philips Attach the sunshield to the camera head. Bosch Security Systems 2022-09 | 2.1 | Installation Manual... - Page 38 MIC IP ultra 7100i │ MIC IP starlight 7100i Make sure that the tabs in the sunshield lock into place in the camera head. Install the M4 x 10 screws. Tighten the screws to 2.2 N m (19.5 in-lb). 2022-09 | 2.1 | Bosch Security Systems Installation Manual...
- Page 39 (Optional) Installing a Sunshield | en M4 x 8 2.2 N m (19.5 in lb) Note that when you install the sunshield correctly, the sunshield appears as in the following figure. Figure 11.1: Sunshield installation is complete. Bosch Security Systems 2022-09 | 2.1 | Installation Manual...
-
Page 40: (Optional) Installing The Illuminator
3. Remove the appropriate access plug from the camera head with the supplied spanner wrench. For upright cameras, remove the plug near the visor. For inverted cameras, remove the plug farther away from the visor. 2022-09 | 2.1 | Bosch Security Systems Installation Manual... - Page 41 MIC IP ultra 7100i │ MIC IP starlight 7100i (Optional) Installing the Illuminator | en Bosch suggests storing the access plug inside the DCA mount (or wall mount accessory) in case it becomes necessary to remove the illuminator. 4. Remove the plastic cap from the illuminator accessory. Discard.
- Page 42 | (Optional) Installing the Illuminator MIC IP ultra 7100i │ MIC IP starlight 7100i 287.93 mm (11.34 in.) 8. Installation of the illuminator is complete. 2022-09 | 2.1 | Bosch Security Systems Installation Manual...
-
Page 43: Optional) Canting The Camera
Do not put a canted (35°) camera in an upright position on the camera base or on an unsecured DCA. In this position, the camera can fall over and can cause injury or be damaged. Put the canted camera on its side until installation. Bosch Security Systems 2022-09 | 2.1 | Installation Manual... - Page 44 Risk of damage to the device. Do not cant the camera, or let it fall, in the wrong direction. The camera should cant only in the direction indicated in the figure directly below. 2022-09 | 2.1 | Bosch Security Systems Installation Manual...
- Page 45 This action removes the slack in the arms and aligns the screw holes properly so that the camera head can move freely. Figure 13.4: Push camera head up 2 mm (0.08 in.) Bosch Security Systems 2022-09 | 2.1 | Installation Manual...
- Page 46 9. Attach the yoke caps using the supplied spanner wrench. Note: Tighten each yoke cap until it is flush with the yoke arm. 0.0mm - 0.5mm Figure 13.6: Attach the yoke caps. 10. Canting is complete. 2022-09 | 2.1 | Bosch Security Systems Installation Manual...
- Page 47 Figure 13.7: Canting is complete. 11. Change the camera orientation to “Canted.” Complete the following steps: – Access the page Configuration. – Navigate to Camera > Installer Menu > Orientation. – Select “Canted.” Bosch Security Systems 2022-09 | 2.1 | Installation Manual...
-
Page 48: Connection
24 VAC. After the High PoE Midspan power source is restored, the camera switches power input again to the High PoE Midspan. Bosch recommends 24VAC power output of 24V at 100VA, 4A with a slow blow fuse. The power supply must be certified to UL/IEC 60950-1 2nd Edition, AM1+AM2 or UL/IEC 62368-1 2nd Ed, Output 24 VAC, LPS, +65 °C (+149 °F) min. -
Page 49: Ethernet Connections
For models with attached illuminators: Use the 95 W midspan sold by Bosch. For models without illuminators: Use the 60 W midspan sold by Bosch, or a midspan that is compliant to the IEEE 802.3at, class 4 standard. Note: Consult the National Electrical Code (NEC) or other regional standards for cable bundling requirements and limitations. -
Page 50: Camera Connections
Note: If the MIC camera will be installed directly to a mounting surface, instead of onto a MIC DCA or a MIC wall mount bracket, Bosch recommends using the connector kit for your model of camera to protect the connections against moisture and dust particles. Each kit provides components for connecting as many as 5 MIC cameras. -
Page 51: Connect The Camera To The Network
5. Attach the ground wire from the camera to an earth-ground connection on the mounting surface using the supplied screw or a suitable user-supplied fastener. 6. If applicable, connect the AUDIO IN and AUDIO OUT wires to the appropriate line level audio device. Bosch Security Systems 2022-09 | 2.1 | Installation Manual... -
Page 52: Installing The Camera Outdoors
| Connection MIC IP ultra 7100i │ MIC IP starlight 7100i 14.6 Installing the camera outdoors 2022-09 | 2.1 | Bosch Security Systems Installation Manual... -
Page 53: Typical System Configurations
Midspan and the head-end network Note: The total length of Cat5e/Cat6 Shielded Twisted Pair (STP) cable must be less than 100 m (328 ft) between the camera and the head-end system. Bosch Security Systems 2022-09 | 2.1 | Installation Manual... -
Page 54: Typical Configuration With Mic-Alm-Was-24
7 Washer pump accessory (user- 8 Interface cable for washer control supplied) (user-supplied) 9 Interface cables for alarm inputs and 10 Switch (monitored, normally open) for outputs (user-supplied) supervised alarm (user-supplied) 2022-09 | 2.1 | Bosch Security Systems Installation Manual... -
Page 55: Troubleshooting
Camera reboots frequently or Your camera has an improper network connection. intermittently Test your camera with another power supply. Check the Bosch website for a software update that might address the issue. 16.1 Physical reset button Each camera has a hardware reset button. You may need to press the reset button to reset the camera to factory defaults if you encounter the following circumstances: –... - Page 56 Let the camera complete a self-check. When the self-check completes, the red LED will go off. Find the IP address again. Access the camera using the web browser. Set the initial service-level password for the camera. 2022-09 | 2.1 | Bosch Security Systems Installation Manual...
-
Page 57: Maintenance
No User-serviceable Parts Except for the external wiper blade, the device contains no user-serviceable parts. Contact your local Bosch service center for device maintenance and repair. In the event of failure, the device should be removed from site for repair. -
Page 58: Replacing A Wiper Assembly
MIC IP ultra 7100i │ MIC IP starlight 7100i 17.1 Replacing a wiper assembly Put a piece of thin, protective material between the window glass and the wiper to prevent accidental damage. 2022-09 | 2.1 | Bosch Security Systems Installation Manual... - Page 59 With one hand, hold the wiper arm firmly in place to restrict rotational movement. With the other hand, using a 7mm Hex socket or nut driver, rotate the acorn nut counter- clockwise until the nut is free from the wiper shaft. Bosch Security Systems 2022-09 | 2.1 | Installation Manual...
- Page 60 | Maintenance MIC IP ultra 7100i │ MIC IP starlight 7100i Remove the wiper spring, hub, arm, and blade assembly from the wiper shaft. 2022-09 | 2.1 | Bosch Security Systems Installation Manual...
- Page 61 MIC IP ultra 7100i │ MIC IP starlight 7100i Maintenance | en Connect the new wiper arm and the new wiper hub. Insert the new blade assembly into the new wiper arm. Bosch Security Systems 2022-09 | 2.1 | Installation Manual...
- Page 62 | Maintenance MIC IP ultra 7100i │ MIC IP starlight 7100i Slide the new wiper hub and the attached parts onto the wiper shaft. 2022-09 | 2.1 | Bosch Security Systems Installation Manual...
- Page 63 MIC IP ultra 7100i │ MIC IP starlight 7100i Maintenance | en Slide the new wiper spring onto the wiper shaft and over the new wiper arm. Bosch Security Systems 2022-09 | 2.1 | Installation Manual...
- Page 64 MIC IP ultra 7100i │ MIC IP starlight 7100i Apply Loctite 243 to the hole of the acorn nut. 10. Lightly thread the new acorn nut onto the wiper shaft over the new wiper spring and new wiper hub. 2022-09 | 2.1 | Bosch Security Systems Installation Manual...
- Page 65 12. With the other hand, using a 7mm Hex socket or nut driver, tighten the new acorn nut clockwise to a torque value of 1.0 Nm. Bosch Security Systems 2022-09 | 2.1 | Installation Manual...
-
Page 66: Decommissioning
The device should only be passed on together with this Installation manual. 18.2 Disposal Disposal - Your Bosch product was developed and manufactured with high-quality material and components that can be recycled and reused. This symbol means that electronic and electrical appliances, which have reached the end of their working life, must be collected and disposed of separately from household waste material. -
Page 67: Technical Data
MIC IP ultra 7100i │ MIC IP starlight 7100i Technical data | en Technical data For product specifications, see the datasheet for your camera, available on the appropriate product pages of the Online Product Catalog at www.boschsecurity.com. Bosch Security Systems 2022-09 | 2.1 | Installation Manual... - Page 68 Support services and Bosch Academy Support Access our support services at www.boschsecurity.com/xc/en/support/. Bosch Building Technologies Academy Visit the Bosch Building Technologies Academy website and have access to training courses, video tutorials and documents: www.boschsecurity.com/xc/en/support/training/ 2022-09 | 2.1 | Bosch Security Systems...
- Page 69 MIC IP ultra 7100i │ MIC IP starlight 7100i Support services and Bosch Academy | Bosch Security Systems 2022-09 | 2.1 | Installation Manual...
- Page 70 | Support services and Bosch Academy MIC IP ultra 7100i │ MIC IP starlight 7100i 2022-09 | 2.1 | Bosch Security Systems Installation Manual...
- Page 72 Bosch Security Systems B.V. Torenallee 49 5617 BA Eindhoven Netherlands www.boschsecurity.com © Bosch Security Systems B.V., 2022 Building solutions for a better life. 202209071631...