Download Print this page

Huawei IPC6126-WDL-E Quick Start Manual page 2

Advertisement

Interface Description/ 接口说明
1
2
5 6
7
8
NO.
Item
Description
序号
名称
说明
Analog video output interface. The interface supports only D1 video output.
1
VIDEO
模拟视频输出接口。该接口仅支持以D1分辨率输出视频。
Audio input/output port.
2
AUDIO
音频输入输出接口。
SD card slot that supports only Micro SD cards of Class 10 or higher classes. You can replace a
Micro SD card only when the device is powered off. When a Micro SD card is used for the first time,
log in to the web page of the device and format the Micro SD card. For details, see Configuration
3
SD CARD
Guide.
SD卡卡槽,仅支持Micro SD卡(Class 10及以上)。请在设备断电的情况下插拔SD卡,否则可能会造成系
统异常。首次使用时,请登录设备Web客户端,格式化SD卡,操作方法请参见《配置指南》。
RS485 interface (D-, D+).
RS485
RS485接口(D-,D+)。
Alarm output interface (1A, 1B).
4
ALM OUT
告警输出接口(1A,1B)。
Alarm input interface (D indicates the positive pole. G indicates the negative pole.).
ALM IN
告警输入接口(D为正极,G为负极)。
System running status indicator.
5
STAT
系统运行状态指示灯。
Interface for connecting the ground cable.
6
GND
用于连接接地线。
Power input interface. Support 12 V DC (±25%) power supply.
7
DC 12V
电源输入接口。支持DC 12V (±25%)。
Reset button. To restart the device, hold down the RST button for less than 3s. To restore the
device to factory defaults, hold down the RST button for at least 3s during the device running or
hold down the RST button, power on the device, and keep holding down the RST button for more
8
RST
than 5s.
重置按钮。运行时按住RST键短于3秒重启设备;运行时按住RST键不短于3秒或者按住RST键后上电并持续按
住RST键不短于5秒后恢复出厂配置。
Network interface. Support power over Ethernet (PoE).
9
PoE
网络接口。支持PoE供电。
3
4
9
CAUTION/ 注意
Exercise caution when restoring the camera to factory settings. After
the camera is restored to factory settings, user account and some other
configuration data may be lost.
恢复出厂配置后将会导致用户的帐号信息以及部分配置信息丢失,请慎重操作。
Indicator Description/ 指示灯说明
Off
The device is powered off.
灯灭
设备未上电。
Steady orange
The system is starting.
橙色长亮
系统正在启动。
The temperature exceeds the upper threshold or falls below the lower threshold and a
Fast flashing red
temperature alarm is generated.
红色快闪
高/低温到达阈值,产生温度告警。
Slow flashing red
Packet loss occurs on the network port or the optical port is abnormal.
红色慢闪
网口丢包、光口异常。
NOTE/ 说明
When the IPC is enabled, the indicator is changed to: Off → Orange → Green.
IPC启动时,STAT指示灯的变化为:灯灭→橙色→绿色。
Prepare for Installation Tools/ 准备安装工具
PVC insulation tape
绝缘胶带
Hammer drill (for mounting a camera on
Marker
记号笔
冲击钻(吊顶和墙壁安装时使用)
Socket wrench (M6)
套筒扳手(M6)
BNC Female to RCA Male Adapter
BNC 母头转 RCA 公头
2
STAT Status Indicator
STAT状态指示灯
Steady green
The system is running properly.
绿色长亮
系统运行正常。
Steady red
The hardware is faulty.
红色长亮
硬件产生故障。
Phillips screwdriver (There are two
Waterproof tape
head models: 1# and 2#)
防水胶带
十字螺丝刀(刀头型号为:1#和2#)
Claw hammer (for mounting a
the ceiling or wall)
camera on the ceiling or wall)
羊角锤(吊顶和墙壁安装时使用)
Cable stripper
RJ-45 connector crimping tool
剥线钳
Glass cement
玻璃胶
水晶头压线钳

Advertisement

loading