Table of Contents
Advertisement
KDC-HD942U
● Specifi cation of the test mode for tuner source
The frequency of 98.3MHz is received when the [4] key is
pressed in the TUNER FM band.
(∗1) Only in the test mode, [1] key, [2] key, [3] key, [4] key,
[5] key and [6] key (K3I) shall be displayed on the multi-
function key.
1. Press the [FNC] key briefl y to make the multi-function
display.
2. Rotate the control knob on the right side and use the
[FM] or [AM] key to display the target key in the center.
3. Press the [ ] key briefl y to fi nalize the display.
(∗2) Perform the same operations as above on the keys, [1],
[2], [3], [4], [5], and [6] of the remote controller.
● TUNER Setup adjustment mode specifi cation
1. Use [FM] or [AM] key to select TUNER band.
2. Press and hold [ ] key for 2 seconds to enter TUNER
adjustment mode. At this point, set FM reception fre-
quency to 98.3MHz at the same time.
3. Use [FM] or [AM] key to change between the adjustment
items.
Soft Mute adjustment
[FM] key
[AM] key
Seek Stop Leve
adjustment
(manual)
(Note) The fi rst item shall be Soft Mute adjustment. But,
in the case of AM band, the fi rst item shall be Seek Stop
Level adjustment (auto) because there is no Soft Mute
adjustment for AM band.
4. Proceed with the following steps for every adjustment
item:
[Soft Mute Adjustment]
This item exists only in TUNER FM. Make adjustment un-
der the condition when VOLUME=30 and LOUD is OFF.
(Display) S M D – x _ _ _ : Adjustment values, 0 ~ 7, are
shown in "x".
a. Adjust the value between 0 (18dBμ)~7 with [
[
] key (possible to press continuously)
b. After the completion of the adjustment, press and hold
[ ] key for 2 seconds to start writing the adjustment
values in E2PROM. At the successful completion of
the writing, "EP_WRITE" is displayed
12
TEST MODE
[AM] key
[FM] key
[AM] key
Seek Stop Leve
adjustment
[FM] key
(auto)
[Seek Stop Level Adjustment (Auto)]
(Display) A T N _ 4. 3 2 V : When at Normal (Local OFF)
(Display) A T L _ 3. 4 5 V : When at Local (Local ON)
a. In the band in which Local Seek ON/OFF is selectable,
Press [AUTO] key briefly to change between Local
Seek ON and OFF.
b. Press and hold [ ] key for 2 seconds to make the cur-
rent receive level to be the seek stop level in order to
start writing the adjustment values in E2PROM. At the
successful completion of the writing, "EP_WRITE" is
displayed. (In this step, use Local Seek ON/OFF setup
to change the destination of the writing.)
[Seek Stop Level Adjustment (Manual)]
(Display) M N N _ 3. 9 8 V : When at Normal (Local OFF)
(Display) M N L _ 4. 4 4 V : When at Local (Local ON)
a. In the band in which Local Seek ON/OFF is selectable,
Press [AUTO] key briefly to change between Local
Seek ON and OFF.
b. Manually adjust the seek stop level between 0.00~
5.00V according to the destination with [
key (possible to press continuously).
c. Press and hold [ ] key for 2 seconds to make the volt-
age that is adjusted in the above step to be the seek
stop level and to start writing the voltage in E2PROM.
At the successful completion of the writing, "EP_
WRITE" is displayed. (In this step, use Local Seek ON/
OFF setup to change the destination of the writing.)
5. Press [ ] key briefly to exit from TUNER Adjustment
mode (and to keep running the Test mode).
● K3I forced switching
Every time when [6] key is pressed in FM band, switched in
the following order: AUTO→Forced WIDE→Forced MIDDLE
→Forced NARROW→AUTO. Default status is AUTO, and
displayed as shown below.
] or
· AUTO
· Forced WIDE
· Forced MIDDLE
· Forced NARROW
Current receive level
Adjustment values: Contents
written in E2PROM as the
initial values are displayed.
] or [
aF1
wF1
mF1
nF1
]
Advertisement
Table of Contents
