NOTE • If you have difficulty in installing this unit in your vehicle, contact your Kenwood dealer. • If it doesn’t seem to be working properly, first press the Reset button. If the malfunction persists, consult your Kenwood dealer.
Safety Precautions 2CAUTION Do not set the remote on hot places such as above the dashboard. Loading and Replacing the Batteries: Use two "AAA" batteries. Slide the cover while pressing downwards to remove it as illustrated. – Insert the batteries with the poles aligned properly, following the illustration inside the case.
Handling Compact Discs Playing a CD that is dirty, scratched or warped can cause the sound to skip and the unit to operate incorrectly, resulting in worsened sound quality. Take the following precautions to prevent your CDs from getting scratched or damaged. Handling CDs •...
Loading Compact Discs "KENWOOD" Projection Make sure the disc magazine is the right way up with the Kenwood logo on the top.Pull the tray out by the projection. Place the disc on the tray with the label facing upwards. Insert the tray into the disc magazine until it locks.
Operations Fast Forwarding and Reversing Disc Play Fast Forwarding Disc Play: Hold down on the ¢ button. Release your finger to play the disc at that point. Reversing Disc Play: Hold down on the 4 button. Release your finger to play the disc at the point. Track Search Search forwards or backwards through the tracks on the disc until you reach the one that you want to listen to.
Direct Disc Search Using the remote control, make direct input of the disc number that you want to listen to. Using the number buttons on the remote control, enter the number of the disc that you want to listen to. The selected disc number blinks in the display for 10 seconds.
Operations Disc Scan Successively play the beginning of each disc on a changer until you find the one that you want to listen to. Starting the disc scan : Press the D.SCAN button. The D.SCN indicator will appear on the display and the player will play the first 10 seconds from each disc in succession.
Changing the Transmission Frequency To set the frequency change mode Hold down the REP button for more than three seconds. The FREQ indicator will light up and the currently set frequency will be displayed. F R E Q M H z NOTE •...
Operations Modulation level / Dynamic control To set the control mode Hold down the RDM button on the display unit for more than three seconds. The LEVEL indicator will light up and the currently set modulation level will be displayed. Modulation level L E V E L Number for prevention of...
Accessories External view External view ... Number of items ...1 ...4 ...4 ...1 ...1 2CAUTION The use of any accessories except for those provided might result in damage to the unit. Make sure only to use the accessories shipped with the unit, as shown above. Installation Procedure 1.
Installation Procedure Angle adjustment switches The angle adjustment switches on the both saides of the unit are to be set according to the angle of installation of the CD auto changer. Set both of the two switches to the same position.
Installation Horizontal installation Cover the holes indicated by (3) with the dustproof seals 5. (Bottom and sides) Use the holes marked (¶) to install the unit. Bottom view Side view Vertical installation Cover the holes indicated by (3) with the dustproof seals 5. (Bottom and sides) Use the holes marked (¶) to install the unit.
Installation Installation of Display unit • Installation without using the trim mount plate Display unit Attach one velcro to the slanted-line of the the display units as shown above, and attach the other velcro to the parts where you wish to attach the display units.
Troubleshooting guide What might seem to be a malfunction in your unit may just be the result of slight misoperation or miswiring. Before calling service, first check the following table for possible problems. PROBLEM The power is not turned on. The wiring harness fuse blows.
PROBLEM Sound skips due to vibration. Something is touching the CD auto-changer. The disc is dirty or damaged. The unit is mounted at a slant. Changer unit is mounted in an unstable place. The angle adjustment switches are set improperly. Nothing appears on the display.
Troubleshooting guide The following messages are displayed when certain problems are occurring in your system. Take the recommended actions. 01 E: No disc magazine has been loaded in the changer. The disc magazine is not completely loaded. Load the disc magazine properly. 02 E: No disc has been loaded in the disc magazine.