Keystone KSTAW06B User Manual page 13

AIR CONDITIONER FEATURES
TO ADJUST FAN SPEEDS:
Press to select the Fan Speed in four steps-Auto,
Low, Med or High. Each time the button is pressed,
the fan speed mode is shifted. On Dry mode,the fan
speed is controlled at Low automatically.
SL EEP FEATURE:
Press Sleep button to initiate the sleep mode. In
this mode the selected temperature will increase by
O O
2 F/1(or 2) C 30 minutes after the mode is selected.
The temperature will then increase by another 2 F/
O
1(or 2) C after an additional 30 minutes. This new
temperature will be m aintained for 6 hours before it
returns to the originally selected temperature. This
ends the Sleep mode and the unit will continue to
operate as originally programmed. The Sleep mode
program can be cancelled at any time during
operation by pressing the Sleep button again.
CHECK FILTER FEATURE:
Press Check filter button to initiate theis feature.
This feature is a reminder to clean the Air Filter for
more efficient operation. The LED(light) will illumi-
nate after 250 hours of operation. To reset after
cleaning the filter, press the Check Filter button and
the light will go off.
ENERGY SAVER FEATURE:
Press En ergy saver button to initiate this function.
This function is a vailable on COOL, DRY, AUTO
(o nly AUTO-COOL ING and AUTO -FAN) modes.Th e
fa n will continue to run for 3 min utes after the
compre ssor sh uts off.Th e fan then cycles on for 2
minutes at 10 minute intervals until the roo m
te mperature is above the se t tempe rature, at wh ich
time the compressor turns b ack on and Cooling
Starts.
FOLLOW ME FEATURE:
Fo llow
M e
En ergy
On/Off
Saver
This feature can be activated from the remote
control ONLY. The remote control serves as
a remote thermost at allowing for the precise
temperature control at its location.
To activate the Follow Me feature, point the remote
control towards the unit and press the Follow Me
button. T he remote dis play is actual temperatur e at
its location. The remote control will send this signal
to the air conditioner every 3 minutes interval until
press the Follow Me button again.
receive the Follow M e signal during any 7 minutes
interval, the unit will beep to indicate the Follow Me
mode has ended.
O
(on some models)
Light flashing
If the unit does not
TO SELECT THE OPE RATING M ODE:
To choose operating mode, press
time you press the button, a mode is selected in a
sequence that goes from Auto, Cool, Dry and Fan. The
indicator light beside will be illuminated and remained
on once the mode is selected.
The unit will initiate automatically the Energy Saver
function under Cool, Dry, Auto(only Auto-Cooling and
Auto-Fan) modes.
To operate on Auto feature:
When you set the air conditioner in AUTO mode, it will
automatically select cooling, heating(cooling only models
without), or fan only operation depending on what
temperature you have selected and the room temperature.
The air conditioner will control room temperature
automatically round the temperature point set by you.
In this mode, the fan speed cannot be adjusted, it starts
automatically at a speed according to the room
temperature.
To operate on Fan Only:
Use this function only when cooling is not desired,such
as for room air circulation or to exhaust stale air(on
some models). (Remember to open the vent during this
function, but keep it closed during cooling for maximum
cooling efficiency.) You can choose any fan speed you
prefer.
During this function, the display will show the actual
room temperature, not the set temperature as in the
cooling mode.
In Fan only mode ,the temperature is not adjusted.
To operate on Dry mode:
In this mode, the air conditioner will generally operate
in the form of a dehumidifier. Since the conditioned
space is a closed or sealed area, some degree of
cooling will continue.
TIM ER: AUTO STA RT/STOP F EATU RE:
When the unit is on or off, first press
TIMER ON indicator light illuminates. It indicates the Auto
Start program is initiated.
When the time of TIMER ON is displayed
button again, the TIMER OFF indicator light illuminates.
It indicates the Auto Stop program is initiated.
Press or hold the UP or DOWN button to change the Auto
time by 0.5 hour increments, up to 10 hours,then at 1 hour
increments up to 24 hours.The control will count down the
time remaining until start.
The selected time will register in 5 seconds, and the system
will automatically revert back to display the previous
temperature setting or room temperature when the unit is
on.(when the unit is off,there is no display.)
Turning the unit ON or OFF at any time or adjusting the
timer setting to 0.0 will cancel the Auto Start/Stop timed
program.
9
Mode button.Each
Timer button, the
,press the Timer