Extron electronics DTP3 T 202 Setup Manual page 3

ATTENTION:
• For unbalanced audio, connect the sleeves to the ground contact. DO NOT connect the sleeves to the negative (–)
contacts.
• Pour l'audio asymétrique, connectez les manchons au contact au sol. Ne PAS connecter les manchons aux
contacts négatifs (–).
LockIt™ Lacing Brackets
Use an included LockIt lacing bracket to securely fasten an HDMI cable to each device as
follows:
1
Plug the HDMI cable into the panel connection.
2 Loosen the HDMI connection mounting screw from the panel enough to allow the
LockIt lacing bracket to be placed over it. The screw does not have to be removed.
3 Place the LockIt lacing bracket on the screw and against the HDMI connector, then
tighten the screw to secure the bracket.
ATTENTION:
• Do not overtighten the HDMI connector mounting screw. The shield it
fastens to is very thin and can easily be stripped.
• Ne serrez pas trop la vis de montage du connecteur HDMI. Le blindage
auquel elle est attachée est très fin et peut facilement être dénudé.
4 Loosely place the included tie wrap around the HDMI connector and the LockIt lacing
bracket as shown.
5 While holding the connector securely against the lacing bracket, use pliers to tighten
the tie wrap, then remove any excess length.
Front Panel Features
DTP3 T 202 Front Panel
CONFIG
e
A B
Figure 6. Front Panels of the DTP3 T 202 and DTP3 R 201
A Power LED — Lights green when the unit is receiving power, either locally or remotely (on the DTP cable).
B
Configuration port — Using a USB cable, connect a PC to this front panel USB C port for remote operation using PCS and
firmware updates.
DTP3 T 202 Rear Panel
C
Send Power toggle switch — In a DTP3 transmitter to DTP3 receiver configuration, set the toggle switch to the UP
(SEND PWR) position on the powered DTP3 device to enable sending remote power to a DTP3 device on the far end. Set
POWER
HDMI HDMI
12V
the toggle switch to the DOWN (OFF) position on the DTP3 device receiving power (see
1.5A MAX
switch configuration).
LOOP OUT INPUT
ATTENTION:
• The DTP3 T 202 and DTP3 R 201 devices are configured to output power to DTP3 models only. If connected to a
A B C
non‑DTP3 device, set the toggle switch to the DOWN (OFF) position. Failure to turn the power OFF will damage the
connected device.
• Le DTP3 T 202 et le DTP3 R 201 sont configurés pour alimenter uniquement les modèles DTP3. S'ils sont connectés
à un autre type d'appareil, veuillez positionner l'interrupteur à bascule sur « DOWN » (OFF). Si l'interrupteur n'est
pas positionné sur OFF, vous risquez d'entraîner la défaillance de l'appareil non DTP3 connecté.
D HDBT/DTP toggle switch (Tx) — Configures the DTP3 Output for either HDBT or DTP mode.
SEND
INPUT
PWR HDBT
SIGNAL
HDCP
OFF DTP DTP3 T 202
C D E
SIG LINK
OVER
TP
RS-232
Tx Rx G
OUT
D E
DTP3 R 201 Front Panel
SEND
PWR
CONFIG
e
OFF
A B C
DTP3 R 201 Rear Panel
SIG
POWER
HDMI
12V
1.5A MAX
OUTPUT DTP3 IN
A F D
1 1 1
3 3 3
4 4 4
3
5 5 5
INPUT
SIGNAL
HDCP
DTP3 R 201
E
LINK
OVER
L R
DTP3
figure 7 on the next page for toggle
RS-232
Tx Rx G AUDIO OUT
E G
2 2 2
3