Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Bluestream SW41AB-V2
Summary of Contents for Bluestream SW41AB-V2
- Page 1 SW41-V2 Coaxial IR Ext. SW41AB-V2 User Manual...
-
Page 2: Table Of Contents
SW41AB-V2 USER MANUAL Contents Thank you for purchasing this product. For optimum performance and safety, please read these instructions carefully Introduction before connecting, operating or adjusting this product. Please keep this manual for future reference. Features Panel Descriptions Infrared Remote Control... -
Page 3: Introduction
SW41AB-V2 USER MANUAL Introduction The SW41AB-V2 is a 4-way HDMI switch with integrated audio breakout. The switch supports full HDMI 2.0 and HDCP 2.2 with video resolutions up to and including 4K @ 60Hz 4:4:4. FEATURES: • Features 4x HDMI inputs which can be switched to a single HDMI output •... -
Page 4: Panel Descriptions
Coaxial digital output (SPDIF) - de-embedded from selected HDMI input Analogue audio Left/Right output (3.5mm stereo jack) - de-embedded from the selected HDMI input. Source input must be PCM 2 channel audio for the analogue output to work. The SW41AB-V2 doesn’t down-mix multi-channel audio signals. -
Page 5: Infrared Remote Control
Blustream IR Control cable 3.5mm Mono to 3.5mm Blustream 5V IR receiver (supplied) to receive IR signal Stereo for linking third party control solutions to Blus- and control the SW41AB-V2 tream products. Compatible with 12V IR third party products. Note: Cable is directional as indicated - not supplied contact support@blustream.co.uk / support@blustream.com.au... -
Page 6: Edid Control
By pre-determining the video resolution and audio format of the sources and display device you can reduce the time needed for EDID hand shaking thus making switching quicker and more reliable. Configuration of extender EDID settings can be achieved using the product dip-switches on the SW41AB-V2. EDID dip-switch settings are shown below. -
Page 7: Application Diagram
SW41AB-V2 USER MANUAL Application Diagram contact support@blustream.co.uk / support@blustream.com.au... -
Page 8: Specifications
• Power Supply: 1x 5V/2A DC NOTE: Specifications are subject to change without notice. Weights and dimensions are approximate. Package Contents • 1 x SW41AB-V2 • 1 x REMSW41 remote control • 1 x 5V/2A DC power supply • 1 x IR receiver (IRR) •... -
Page 9: Rs-232 Control
USER MANUAL RS-232 Control The SW41AB-V2 switch can be controlled via a 9-pin serial cable. See page 11 for the full list of control protocols. Details of RS-232 pin assignment and communication are below. Please note that depending on your control device serial port pin configuration you may require either a ‘Straight’... -
Page 10: Rs-232 Commands
Reset System To Default Setting (Should Type “Yes” To Confirm, “No” To Discard) OUTFRyy Set OUTPUT From INPUT:yy OUTON/OFF Set OUTPUT Port On or Off SW41AB-V2 IR Commands SW41 NEC IR: CUSTOMER CODE 1898 HEX IR 0000 006D 0000 0022 0157 00AC 0016 0016 0016 0016 0016 0016 0016 0041 0016... -
Page 11: Installer Notes
SW41AB-V2 USER MANUAL Installer notes: contact support@blustream.co.uk / support@blustream.com.au... - Page 12 www.blustream.co.uk www.blustream.com.au...
Need help?
Do you have a question about the SW41AB-V2 and is the answer not in the manual?
Questions and answers