Feit Electric SL20-10/SOL/EU Manual

MODEL: SL20-10/SOL/EU
ITM. / ART.
1193824
SOLAR LED STRING LIGHTS
CONTENTS:
1 6m LED String Light Set with 10 sockets................................
1 6m Solar Panel Cable...........................................................
1 Solar Panel................................................................................
1 Solar Panel Wall Mount........................................................
1 Solar Panel Ground Stake...............................................................
12 Low Voltage 3.7 Volt
(with red ring)
2 Mounting Screws...............................................................................
INSTRUCTIONS:
Carefully remove the product from package and make sure that
1
all the parts are included by referencing the contents above.
Gently remove the clear plastic film from the solar panel to
2
charge battery.
Charge solar panel for at least 6 hours by exposing solar
3
panel face to sunlight.
Install light bulbs. Hold the socket in one hand and twist bulb
4
clockwise. Make sure bulbs are tightly installed for proper
contact and to prevent moisture from getting in the sockets.
THIS PRODUCT ONLY WORKS WITH
LOW VOLTAGE 3.7 VOLT LIGHT BULBS
RED RING
ONLY USE WITH LOW VOLTAGE
Once solar panel is charged, test the unit before hanging.
5
Connect string light cord to solar panel cable and connect solar
panel cable to solar panel. Press power button to turn on set.
If any bulb does not light, tighten it further.
Solar panel has a built-in timer.
6
Toggle Left: On at dusk, Off after 6 hours.
Toggle Right: On at dusk and Off at dawn or
when battery discharges.
BACK OF SOLAR PANEL
ON AT DUSK.
OFF AFTER
6 HOURS.
POWER
ON/OFF
WHEN NOT IN USE, TURN POWER BUTTON OFF
TO EXTEND BATTERY LIFE
1 of 2
Light Bulbs ................
(2 extra)
LED BULBS WITH RED RING
CONNECT SOLAR
PANEL CABLE TO
BACK OF SOLAR PANEL.
THEN SECURE BY
TURNING CLOCKWISE.
ON AT DUSK. ON AT DUSK.
OFF AFTER
OFF AT DAWN.
6 HOURS.
ON AT DUSK.
POWER
ON/OFF
OFF AT DAWN.
FEIT ELECTRIC COMPANY | PICO RIVERA, CA, U.S.A. www.feit.com
7
Choose the best location for your solar panel:
For best results, select a location with full and direct sunlight.
If installed in a shady area, the battery will take a longer time
to charge, may not fully charge and reduce working hours.
Operating time should be up to 8 hours with full charge. For
optimal performance at night, the solar panel should receive
approximately 8 hours of sunlight per day.
Do not install near night-time light sources such as porch lights
or street lights. These light sources may cause the unit to turn off
because of the built-in dusk to dawn sensor on solar panel.
CAUTION:
Avoid impacts to the solar panel.
Install solar panel away from other light sources.
Use caution when handling the ground stake.
Replace bulbs when needed with Feit Electric, 3.7 volt light bulb
with a red ring only.
If you need assistance finding a replacement bulb please
contact Feit Electric at info@feit.com.
MAINTENANCE:
For best battery efficiency, clean solar panel at regular intervals.
Wipe off dust, dirt, snow etc. Turn off switch during maintenance.
Do not use chemical solvents on the bulbs. Wipe clean with a cloth.
To extend the life of the battery, turn the unit off using the power
on/off button on the back of solar panel when not in use.
TROUBLE SHOOTING:
If any bulb does not light, tighten it.
If tightening bulb does not work,
disconnect string light from solar panel
and make sure the bulb base is making
contact with bottom tab inside the light socket.
LIMITED WARRANTY
This product is warranted to be free from defects in workmanship and materials for up to 2 years
from date of purchase. If it fails to do so, please contact Feit Electric at info@feit.com for instructions
on replacement. This replacement is the sole remedy available and liability for incidental or
consequential damage is expressly excluded. For comments please contact: Feit Electric Customer
Service 4901 Gregg Road, Pico Rivera, CA 90660 USA. www.feit.com
This device complies with part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause undesired operation. This
equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or more of the following
measures: Reorient or relocate the receiving antenna. Increase the separation between the
equipment and receiver. Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help.
Any changes or modifications not expressly approved by the manufacturer could void the user's
authority to operate the equipment.
The performance specifications (charge
time, hours of operation) printed on this
manual should only be considered an
approximation of expected performance.
CONTACT
TAB
IF CONTACT TAB IS FLATTENED,
LIFT IT UP USING YOUR FINGER
RATED
IP65