Related Manuals for JWA BURGESS 76421
Summary of Contents for JWA BURGESS 76421
- Page 1 ASSEMBLY INSTRUCTION BURGESS BUFFET ITEM CODE 76421 Imported by JWA Furniture Pty Ltd, Qld, Brisbane Australia. For any assistance with assembly or for missing parts please refer to your receipt...
-
Page 2: Pre-Assembly Preparation
PRE-ASSEMBLY PREPARATION Before you start: 1.Choose a clean, level, spacious assembly area. Avoid hard surfaces that may damage the product 2.Take care when li�ing. Product should be assembled as near as possible to the point of 3.Ensure that you have all required contents for complete assembly 4.Always read the assembly instruc�ons carefully before beginning assembly. -
Page 3: Parts List
PARTS LIST... - Page 4 PARTS LIST ITEM QTY NO. ITEM 8PCS 20PCS Φ6*35 20PCS 8PCS Φ15*10 Φ6*60 30PCS 56PCS Φ4*14 Φ6*30 16PCS 4PCS Φ4*50 2PCS 5PCS 12PCS 36PCS Φ4*35 Φ3*12 24PCS 6PCS Φ3*16 24PCS 4PCS 8PCS 8PCS 24PCS 4PCS Φ4*14 3PCS 8PCS...
- Page 5 PARTS LIST ITEM QTY NO. ITEM 2 PCE TOP PANEL 1 PC LEGS SUPPORT PANEL 1 PC LEFT SIDE PANEL 1 PC LEGS SUPPORT PANEL 1 PC 1 PC RIGHT SIDE PANEL LEGS SUPPORT PANEL 1 PC 2 PCE BOTTOM PANEL SHELF PANEL 6 PCE 2 PCE...
- Page 6 STEP 1: STEP 2:...
- Page 7 STEP 3:...
- Page 8 STEP 4: STEP 5:...
- Page 9 STEP 6: STEP 7:...
- Page 10 STEP 8: STEP 9:...
- Page 11 STEP 10: STEP 11:...
- Page 12 STEP 12: STEP 13:...
- Page 13 STEP 14: STEP 15:...
- Page 14 STEP 16: STEP 17:...
- Page 15 STEP 18: STEP 19:...
- Page 16 STEP 20: Assemble these four holes first, adjust the door and ensure it is level, then tighten all screws. How to adjust the door and ensure it is level, please see the below information. INFORMATION...
- Page 17 STEP 21: STEP 22: To insert Drawers: a) Bring the ball-bearing slider on Drawer Glide Track(S1) forward to the front edge of(S1). b) Align the back open-end of the Drawer Glide Runner(S2) on each side of the drawer to fit squarely into the groove on the open front-end of(S1).Be sure the drawer/M 2 is not tilted or angled, and gently push in drawer squarely.
- Page 18 STEP 23: STEP 24: WALL...
- Page 19 ASSEMBLY IS COMPLETE CAUTION：Always Lift Your Furniture When Moving /Relocating - Do Not Drag. Dragging Can Cause The Legs To Bend/Break.
- Page 20 SAFETY BRACKETS INSTRUCTIONS 1. Attach one Mounting Plate to the wall with the Large Screws. Make sure to attach the Mounting Plate into a stud. If mounting into brick or masonry you will need to acquire wall anchors. 2. Attach the second Mounting Plate to the furniture frame with the Short Screws.
- Page 21 To protect your furniture, we suggest the following: • Avoid placing your furniture in direct sunlight. • Do not place furniture directly under windows. • Do not place sharp materials (knife, fork, etc.) directly onto your furniture as sharp material may scrape and damage the finish.
Need help?
Do you have a question about the BURGESS 76421 and is the answer not in the manual?
Questions and answers