Table of Contents
Advertisement
Advertisement
Table of Contents
Summary of Contents for BRP VIBE
- Page 1 VIBE COMMUNICATION SYSTEM USER GUIDE...
- Page 2 USER GUIDE VIBE ENGLISH...
-
Page 3: Contents
Ride connected with the comm system designed for year-round use. On snow, Vibe’s battery life allows you to talk and listen for up to 8 hours at -20c/4F. Battery life is even better in moderate and warm temperatures. -
Page 4: Table Of Contents
A. GENERAL ..............4 G. TROUBLESHOOTING GUIDE ......... 17 1. SAFETY INFORMATION 2. MINIMAL REQUIREMENT H. ACCESSORIES AND SPARE PARTS ..... 18 B. VIBE COMMUNICATION SYSTEM ......5 1. ACCESSORIES 1. ANATOMY OF THE VIBE 2. REPLACEMENT PARTS 2. VIBE INSTALLATION (HELMET PREPARATION) 3. -
Page 5: General
WARNING To install the VIBE communication system, you must be at least equipped with a BRP compatible helmet. To be able to connect your phone to the Indicates a hazardous situation which, if not avoided, could result in death Vibe communication system, you will need a compatible Smartphone, or serious injury. -
Page 6: Vibe Communication System
B. VIBE COMMUNICATION SYSTEM 1. ANATOMY OF THE VIBE WARNING BRP recommends that you always find out about the local road safety rules regarding helmets equipped with a noise control system and/or a Antenna Main Unit communication system. Always abide to applicable laws and Speaker regulations where vehicle is driven. -
Page 7: Vibe Installation
B. VIBE COMMUNICATION SYSTEM REMOVING THE REAR TRIM 3. VIBE INSTALLATION INSTALLING THE MAIN UNIT 5. Using either marking on the rear trim, 1. Place the “Main Unit” in the slot left by push the trim away from the helmet by the EPS from previous step. -
Page 8: Option A: Speakers With Ncs
B. VIBE COMMUNICATION SYSTEM INSTALLING THE ANTENNA 4.1. OPTION A: SPEAKERS WITH NCS 7. Slide the antenna into the hole on the A.1. Remove the NCS (Noise Control right. System) from the helmet (held by Velcro 8. Pass the wire into the slot and hole. -
Page 9: Option B: Speakers Without Ncs
B. VIBE COMMUNICATION SYSTEM A.6. Using the Velcro , position and fix 4.2. OPTION B: SPEAKERS WITHOUT NCS the speaker inside the NCS. B.1. Remove the NCS from the helmet (held by Velcro). A.7. Reinstall the NCS into the helmet,... -
Page 10: Option C: Speakers With Ear Pad
B. VIBE COMMUNICATION SYSTEM 4.3. OPTION C: SPEAKERS WITH EAR PAD 5. MICROPHONE INSTALLATION 1. Take the adhesive Velcro from the accessories box supplied with your C.1. Remove the EarPad from the VIBE. helmet (held by Velcro). 2. Install the Velcro and apply uniform pressure on the adhesive. -
Page 11: Installing The Cheeck Pads
1. BRP GO! app trim. Reposition the trim onto the helmet Use the free BRP GO! app for easy setup and management of your Vibe so that it snaps magnetically in place. device as well as to view full support documentation. -
Page 12: Sena Device Manager
Note: • The VIBE communication product will not charge if the system is on but will let you use it while it is plugged in. You need to turn off the VIBE communication system to charge it. • Any 3rd party USB charger can be used with this product if the charger is approved by either the FCC, CE, IC, or other locally approved agencies. -
Page 13: Vibe Basic Function
1. ANATOMY OF THE USER INTERFACE 3. QUICK PAIRING To pair your Vibe to your phone, you will first need to access the configuration menu by holding the center button for 3 sec. You can then go to phone pairing by tapping the “up” button once. Tap the center button to select “phone pairing”. -
Page 14: Vehicle Pairing
To change the prompt voice volume, you need to be out of the mesh the center button to select “vehicle pairing”. Then, on your vehicle display, intercom without music playing. go to Bluetooth settings and select your vibe product in the list of available devices. MEDIA / MUSIC: The music volume can be changed when the music is playing and when 5. -
Page 15: Music Control
MUTE / UNMUTE MICROPHONE: WARNING Press the center button to mute / unmute BRP recommends always keeping your focus on the road/trail. Use your the microphone. Vibe communication system only when conditions are safe. WARNING Prolonged exposure to loud music can damage hearing; BRP... -
Page 16: Voice Assistant (Apple Or Google)
2. Factory reset To factory reset your Vibe, go in the config menu by pressing the configuration button for 3 seconds, then using the joystick go up 5 times until you hear the voice prompt “Factory reset” and click the joystick center... -
Page 17: Other Important Information
Do not attempt to charge a battery with a damaged charger. This could damage the battery, cause an explosion or an accident. Use only original parts, replacement parts and accessories that BRP has expressly approved for your communication system! CAUTION If the product becomes hot or swells during charging or use, immediately stop charging or using the product. -
Page 18: Troubleshooting Guide
G. TROUBLESHOOTING GUIDE Fault Reset When your Vibe is not working properly, you can easily reset the unit by pressing the pinhole reset button, located next to the USB port on your Vibe. The Vibe will shut down. PROBLEM ACTION... -
Page 19: Accessories And Spare Parts
BRP dealers in your area, use the dealer search on the BRP website: dealer. www.brp.com BRP asks that you provide a precise description of the claim as well as a copy of your receipt. Note: For more information on available replacement parts, please visit our website at the following address: http://store.ski-doo.com/... - Page 20 15/F Parale Mitsui Building,8 Higashida-Cho, Kawasaki-ku Kawasaki 210-0005 Japan For your nearest authorized BRP dealer or distributor or for more information on BRP products, please visit our web site: Room Dubai, level 12, Platinum www.brp.com Tower ® ™ and the BRP logo are trademarks of Bombardier Recreational Products inc. or its affiliates.