Garmin A03113 Owner's Manual page 21

1
Select NAV INFO > User Data > Routes.
2
Select a route.
3
Select Navigate To.
4
Select an option:
• To navigate the route from the starting point used when
the route was created, select Forward.
• To navigate the route from the destination point used
when the route was created, select Backward.
A magenta line appears. In the center of the magenta line is
a thinner purple line that represents the corrected course
from your present location to the destination. The corrected
course is dynamic, and it moves with your boat when you are
off course.
5
Review the course indicated by the magenta line.
6
Follow the magenta line along each leg in the route, steering
to avoid land, shallow water, and other obstacles.
7
If you are off course, follow the purple line (corrected course)
to go to your destination, or steer back to the magenta line
(direct course).
Browsing for and Navigating Parallel to a Saved
Route
Before you can browse a list of routes and navigate to one of
them, you must create and save at least one route.
1
Select NAV INFO > User Data > Routes.
2
Select a route.
3
Select Navigate To.
4
Select Offset to navigate parallel to the route, offset from it
by a specific distance.
5
Indicate how to navigate the route:
• To navigate the route from the starting point used when
the route was created, to the left of the original route,
select Forward Port.
• To navigate the route from the starting point used when
the route was created, to the right of the original route,
select Forward Starboard.
• To navigate the route from the destination point used
when the route was created, to the left of the original
route, select Backward Port.
• To navigate the route from the destination point used
when the route was created, to the right of the original
route, select Backward Starboard.
6
If necessary, select Done.
A magenta line appears. In the center of the magenta line is
a thinner purple line that represents the corrected course
from your present location to the destination. The corrected
course is dynamic, and it moves with your boat when you are
off course.
7
Review the course indicated by the magenta line.
8
Follow the magenta line along each leg in the route, steering
to avoid land, shallow water, and other obstacles.
9
If you are off course, follow the purple line (corrected course)
to go to your destination, or steer back to the magenta line
(direct course).
Deleting a Saved Route
1
Select NAV INFO > User Data > Routes.
2
Select a route.
3
Select Review > Delete.
Deleting All Saved Routes
Select NAV INFO > User Data > Clear User Data > Routes.
Navigation with a Chartplotter
Auto Guidance
The Auto Guidance feature is based on electronic chart
information. That data does not ensure obstacle and bottom
clearance. Carefully compare the course to all visual sightings,
and avoid any land, shallow water, or other obstacles that may
be in your path.
NOTE: Auto Guidance is available with premium charts, in some
areas.
You can use Auto Guidance to plot the best path to your
destination. Auto Guidance uses your chartplotter to scan chart
data, such as water depth and known obstacles, to calculate a
suggested path. You can adjust the path during navigation.
Setting and Following an Auto Guidance Path
1
Select a destination (Destinations, page
2
Select Navigate To > Auto Guidance.
3
Review the path, indicated by the magenta line.
4
Select Start Navigation.
5
Follow the magenta line, steering to avoid land, shallow
water, and other obstacles.
NOTE: When using Auto Guidance, a gray segment within
any part of the magenta line indicates that Auto Guidance
cannot calculate part of the Auto Guidance line. This is due to
the settings for minimum safe water depth and minimum safe
obstacle height.
Creating and Saving an Auto Guidance Path
1
Select NAV INFO > User Data > Routes > New > Auto
Guidance.
2
Select a starting point, and select Next.
3
Select a destination, and select Next.
4
Select an option:
• To view a hazard and adjust the path near a hazard,
select Hazard Review.
• To adjust the path, select Adjust Path, and follow the on-
screen instructions.
• To delete the path, select Cancel Auto Guidance.
• To save the path, select Done.
Adjusting a Saved Auto Guidance Path
1
Select NAV INFO > User Data > Auto Guidance Path.
2
Select a path, and select Review > Edit > Adjust Path.
TIP: When navigating an Auto Guidance path, select the path
on the navigation chart, and select Adjust Path.
3
Select a location on the path.
4
Drag the point to a new location.
5
If necessary, select a point, and select Remove.
6
Select Done.
Canceling an Auto Guidance Calculation in Progress
From the Navigation chart, select MENU > Cancel.
TIP: You can select BACK to quickly cancel the calculation.
Setting a Timed Arrival
You can use this feature on a route or an Auto Guidance path to
get feedback about when you should arrive at a selected point.
This allows you to time your arrival at a location, such as a
bridge opening or a race starting line.
1
From the Navigation chart, select MENU.
2
If necessary, select Navigation Options.
3
Select Timed Arrival.
TIP: You can quickly open the Timed Arrival menu by
selecting a point on the path or route.
CAUTION
11).
13